Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Section 189 (Lighting System): Inspection
- HEADLAMP DIMMER SWITCH ASSY
- Inspect light control switch continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
LIGHT CONTROL SWITCH CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity TAIL 14-16 Continuity HEAD 13-16 - 14 Continuity AUTO 12 - 16 Continuity - Inspect headlight dimmer switch continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
HEADLIGHT DIMMER SWITCH CONTINUITYSwitch operation Tester connection Specified condition FLASH 7-8-16 Continuity LOW BEAM 16 - 17 Continuity HI BEAM 7 - 16 Continuity - Inspect turn signal switch continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
TURN SIGNAL SWITCH CONTINUITYSwitch operation Tester connection Specified condition Right turn 2 - 3 Continuity Neutral - No continuity Left turn 1 - 2 Continuity - Inspect front fog light switch continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
FRONT FOG LIGHT SWITCH CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity ON 11 - 18 Continuity
- Inspect light control switch continuity.
- HAZARD WARNING SIGNAL SWITCH ASSY
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
HAZARD WARNING SIGNAL SWITCH TERMINAL CONTINUITYSwitch operation Tester connection Specified condition OFF 3 - 4 No continuity ON 3-4 Continuity Illumination circuit 5 - 6 Continuity - Inspect illumination operation.
- Connect the positive (+) lead from the battery to the terminal 6 and negative (-) lead to the terminal 5, then check that the illumination comes on.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
- FRONT DOOR COURTESY LAMP SWITCH ASSY
- Check that there is continuity between the terminal and the switch body when the switch is operated.
Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity
- Check that there is continuity between the terminal and the switch body when the switch is operated.
- REAR DOOR COURTESY LAMP SWITCH ASSY
- Check that there is continuity between the terminal and the switch body when the switch is operated.
Standard:
ON (When shaft is pressed): No continuity
OFF (When shaft is not pressed): Continuity
- Check that there is continuity between the terminal and the switch body when the switch is operated.
- BACK DOOR LOCK ASSY (W/O POWER BACK DOOR)
- Inspect back door courtesy lamp switch operation.
- Check that there is continuity between the terminal 5 and the terminal 6 when the back door is open and closed.
Standard:
Back door is open: No continuity
Back door is closed: Continuity
- Inspect back door courtesy lamp switch operation.
- BACK DOOR LOCK ASSY (W/ POWER BACK DOOR)
- Inspect back door courtesy lamp switch operation.
- Check that there is continuity between the terminal 3 and the terminal 4 when the back door is open and closed.
Standard:
Back door is open: No continuity
Back door is closed: Continuity
- Inspect back door courtesy lamp switch operation.
- HEADLAMP RELAY
- Inspect relay continuity.
Standard:
HEADLAMP RELAY CONTINUITYCondition Tester connection Specified condition Always 1 - 2 Continuity Always 3 - 5 No continuity Apply B+ between the terminal 1 and 2 3 - 5 Continuity - TAIL LAMP RELAY
- FOG LAMP RELAY
- RUNNING LIGHT RELAY
- HEADLAMP DAY DIM LIGHT RELAY
- BRK RELAY
- KEY CYLINDER LAMP ASSY
- Connect the battery positive (+) lead to the terminal 1 and the battery negative (-) lead to the terminal 2, and check that the indicator light comes on.
- TRANSPONDER KEY AMPLIFIER
- Inspect key cylinder lamp operation.
- Connect the battery positive (+) lead to the terminal 2 and the battery negative (-) lead to the terminal 6, and check that the indicator light comes on.
- Inspect key cylinder lamp operation.
- ROOF CONSOLE BOX ASSY
- AIR OUTLET REGISTER ASSY NO. 1
- Inspect interior light LH No. 1 continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
INTERIOR LIGHT LH NO. 1 CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity DOOR 2 - 3 Continuity ON 1 - 2 Continuity
- Inspect interior light LH No. 1 continuity.
- AIR OUTLET REGISTER ASSY NO. 2
- Inspect interior light RH No. 1 continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
INTERIOR LIGHT RH NO. 1 CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity DOOR 2 - 3 Continuity ON 1 - 2 Continuity
- Inspect interior light RH No. 1 continuity.
- AIR DUCT REGISTER ASSY NO. 3
- Inspect interior light LH No. 2 continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
INTERIOR LIGHT LH NO. 2 CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity DOOR 2 - 3 Continuity ON 1 - 2 Continuity
- Inspect interior light LH No. 2 continuity.
- AIR OUTLET REGISTER ASSY NO. 4
- Inspect interior light RH No. 2 continuity.
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
INTERIOR LIGHT RH NO. 2 CONTINUITYSwitch operation Tester connection Specified condition OFF - No continuity DOOR 2 - 3 Continuity ON 1 - 2 Continuity
- Inspect interior light RH No. 2 continuity.
- FRONT DOOR TRIM BOARD SUB-ASSY LH
- Inspect front door courtesy lamp.
- Check that the continuity exists between the terminals.
Standard: There is continuity
- Inspect front door courtesy lamp.
- FRONT DOOR TRIM BOARD SUB-ASSY RH
- Inspect front door courtesy lamp.
- Check that the continuity exists between the terminals.
Standard: There is continuity
- Inspect front door courtesy lamp.
- REAR DOOR COURTESY LAMP ASSY LH
- Check that the continuity exists between the terminals.
Standard: There is continuity
- Check that the continuity exists between the terminals.
- REAR DOOR COURTESY LAMP ASSY RH
- Check that the continuity exists between the terminals.
Standard: There is continuity
- Check that the continuity exists between the terminals.
- ROOM LAMP ASSY NO. 2
- Check that the continuity exists between the terminals.
Standard: There is continuity
- Check that the continuity exists between the terminals.
- LH VISOR ASSY
- Inspect vanity light continuity.
- Check that the continuity exists between the terminal 1 and the terminal 2 when the light is operated.
Standard:
OFF (closed): No continuity
ON (opened): Continuity
- Inspect vanity light continuity.
- RH VISOR ASSY
- Inspect vanity light continuity.
- Check that the continuity exists between the terminal 1 and the terminal 2 when the light is operated.
Standard:
OFF (closed): No continuity
ON (opened): Continuity
- Inspect vanity light continuity.
- HEADLAMP LEVELING SWITCH
- Connect the battery positive (+) lead to the terminal 1 and the battery negative (-) lead to the terminal 5.
- Measure the resistance between the terminal 4 and the battery negative (-) lead when headlamp leveling switch is operated.
- Measure the resistance between the terminal 5 and the battery negative (-) lead when headlamp leveling switch is operated.
Standard:
HEADLAMP LEVELING SWITCH RESISTANCESwitch position Specified voltage (V) 0 9.0 to 12.6 1 7.9 to 11.1 2 6.9 to 9.6 3 5.8 to 8.2 4 4.7 to 6.6 5 3.7 to 5.1 - Inspect switch illumination.
- Connect the battery positive (+) lead to the terminal 3 and the battery negative (-) lead to the terminal 6, and check that the illumination comes on.
- STOP LAMP SWITCH ASSY
- Check the continuity between the terminals at each switch position as shown in the chart.
Standard:
STOP LAMP SWITCH CONTINUITYSwitch position Tester connection Specified condition Switch pin free 1 - 2 No continuity Switch pin free 3 - 4 Continuity Switch pin pushed in 1 - 2 Continuity Switch pin pushed in 3-4 No continuity
- Check the continuity between the terminals at each switch position as shown in the chart.
- INTERIOR DOME LAMP SWITCH ASSY
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Standard:
- Check that there is continuity between the terminals at each switch position as shown in the chart.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
