2004 Lexus ES 330FACTORY OEM SERVICE PROCEDURE

Section 178 (Automatic Transmission Assembly): Replacement

WARNING: This page is about a different car, the 2004 Toyota Sienna. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (See  REPLACEMENT  ) 
  2. REMOVE FRONT DRIVE SHAFT ASSY LH (See  REMOVAL & INSTALLATION  ) 

    SST 09520-01010, 09520-24010 (09520-32040)

  3. REMOVE FRONT DRIVE SHAFT ASSY RH (2WD DRIVE TYPE) (See  REMOVAL & INSTALLATION  ) 
  4. REMOVE FRONT DRIVE SHAFT ASSY RH (4WD DRIVE TYPE)(See  REMOVAL & INSTALLATION  ) 

    SST 09520-01010, 09520-24010 (09520-32040)

  5. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO. 2 
    1. Remove the bolt and transmission control cable bracket No. 2.
    Fig 1: Removing Transmission Control Cable Bracket No. 2
    G03062847Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE WIRE HARNESS CLAMP 
    1. Disconnect the wire harnesses from the clamps.
    2. Remove the 3 bolts and 2 clamps.
    Fig 2: Removing Wire Harness Clamp
    G03062848Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. DISCONNECT WIRE HARNESS 
    1. Remove the bolt and wire harness.
    Fig 3: Disconnecting Wire Harness
    G03062849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE STARTER ASSY 
    1. Remove the nut and disconnect the starter wire.
    2. Disconnect the connector.
    3. Remove the 2 bolts and starter assy.
    Fig 4: Removing Starter Assembly
    G03062850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. DISCONNECT CONNECTOR 
    1. Disconnect the 2 transmission wire connectors.
    2. Disconnect the park/neutral position switch connector.
    3. Disconnect the 2 transmission revolution sensor connectors.
    Fig 5: Disconnecting Wiring Harness Connectors
    G03062851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO. 1 
    1. Remove the bolt and oil cooler tube clamp.
    2. Remove the 2 bolts and transmission control cable bracket No. 1.
    Fig 6: Removing Transmission Control Cable Bracket No. 1
    G03062852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSY 
    1. Remove the ATF level gauge.
    2. Disconnect the wire harnesses 2 clamps from the oil filler tube.
    3. Remove the 2 bolts and oil filler tube.
    4. Remove the O-ring from the oil filler tube.
    Fig 7: Removing Transmission Oil Filler Tube Sub-Assembly
    G03062853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE OIL COOLER INLET TUBE NO. 1 
    1. Using SST and spanner, disconnect the oil cooler inlet tube No. 1.

      SST 09023-12700

  13. REMOVE OIL COOLER OUTLET TUBE NO. 1 
    1. Using SST and spanner, disconnect the oil cooler outlet tube No. 1.

      SST 09023-12700

    Fig 8: Removing Oil Cooler Outlet Tube No. 1
    G03062854Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE ENGINE MOUNTING BRACKET FR 
    1. Remove the 3 bolts and engine mounting bracket FR.
    Fig 9: Removing Engine Mounting Bracket FR
    G03062855Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE AUTOMATIC TRANSAXLE ASSY (2WD DRIVE TYPE) 
    1. Remove the 2 bolts and flywheel housing under cover.
      Fig 10: Removing Flywheel Housing Under Cover (2WD Drive Type)
      G03062856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.
      Fig 11: Removing Torque Converter Clutch Mounting Bolt (2WD Drive Type)
      G03062857Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 8 bolts.
    4. Separate and remove the automatic transaxle.
    Fig 12: Removing Automatic Transaxle (2WD Drive Type)
    G03062858Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. REMOVE TRANSFER STIFFENER PLATE RH (4WD DRIVE TYPE) 
    1. Remove the 5 bolts, nut and transfer stiffener plate RH.
    Fig 13: Removing Transfer Stiffener Plate RH (4WD Drive Type)
    G03062859Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE AUTOMATIC TRANSMISSION W/TRANSFER (4WD DRIVE TYPE) 
    1. Remove the 2 bolts and flywheel housing under cover.
      Fig 14: Removing Flywheel Housing Under Cover (4WD Drive Type)
      G03062860Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.
      Fig 15: Removing Torque Converter Clutch Mounting Bolt (4WD Drive Type)
      G03062861Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 8 bolts.
    4. Separate and remove the automatic transaxle w/transfer.
    Fig 16: Removing Automatic Transaxle W/Transfer (4WD Drive Type)
    G03062862Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE TRANSFER ASSY (4WD DRIVE TYPE) (See  OVERHAUL  ) 
  19. REMOVE TORQUE CONVERTER CLUTCH ASSY 
  20. INSPECT TORQUE CONVERTER CLUTCH ASSY (See  INSPECTION  ) 

    SST 09350-32014 (09351-32010, 09351-32020)

  21. INSTALL TORQUE CONVERTER CLUTCH ASSY 
    1. Install the torque converter clutch to the automatic transaxle.
    2. Using vernier calipers, measure the dimension "A" between the transaxle fitting part the converter fitting part of the drive plate.
      Fig 17: Measuring Dimension "A"
      G03062863Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using vernier calipers and a straight edge, measure the dimension "B" shown in the illustration and check that "B" is greater than "A" measured in (b).

      Standard: A + 1 mm or more 

    NOTE: Do not add the thickness of straight edge.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.