2003 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Section 573 (Front/Rear Axle): Replacement

WARNING: This page is about a different car, the 2004 Lexus SC 430. However, it is still accessible from the selected car via links, so may be relevant.

HINT:

  • COMPONENTS (See COMPONENTS 
  • Use the same procedures for the RH side and LH side.
  • The procedures listed below are for the LH side.
  • A bolt without a torque specification is shown in the standard bolt table (See SPECIFIED TORQUE FOR STANDARD BOLTS ).
  1. REMOVE FRONT WHEEL LH 
    1. Remove the 10 bolts and ornament.
    2. Remove the 5 nuts and wheel.
  2. DISCONNECT SPEED SENSOR FRONT LH 
    1. Remove the bolt and separate the speed sensor from the steering knuckle.
  3. DISCONNECT DISC BRAKE CYLINDER ASSY LH 
    1. Remove the 2 bolts and brake cylinder from the steering knuckle.
      Fig 1: Removing Brake Cylinder
      G02957807Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Support the brake cylinder securely.
  4. REMOVE FRONT DISC 
  5. REMOVE STEERING KNUCKLE ASSY LH 
    1. Remove the clip and nut of the upper side.
    2. Using SST, disconnect the steering knuckle from the upper suspension arm.

      SST 09610-20012

      Fig 2: Disconnecting Steering Knuckle From Upper Suspension Arm
      G02957808Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 bolts and the steering knuckle from the lower ball joint.

      Torque: 113 N.m (1,150 kgf.cm, 83 ft.lbf) 

      Fig 3: Removing Steering Knuckle From Lower Ball Joint
      G02957809Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE FRONT AXLE HUB GREASE CAP LH 
    1. Using a screwdriver, pry out the grease cap from the steering knuckle.
  7. REMOVE FRONT AXLE LOCK NUT 
    1. Clamp the axle hub in a soft jaw vise.
      NOTE: Close the vise until it holds the hub bolt. Do not tighten excessively. 
    2. Using a chisel and hammer, loosen the staked part of the lock nut.
    3. Using a 36 mm socket wrench, remove the lock nut.
      Fig 4: Removing Front Axle Lock Nut
      G02957810Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE SKID CONTROL ROTOR FRONT 
  9. DISCONNECT DISC BRAKE DUST COVER FRONT LH 
    1. Remove the 4 bolts and shift the brake dust cover toward the outside.
  10. REMOVE FRONT AXLE HUB SUB-ASSY LH 
    1. Using SST, remove the axle hub from the steering knuckle.

      SST 09950-40011 (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)

      Fig 5: Removing Axle Hub From Steering Knuckle
      G02957811Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE BEARING INNER RACE 
    1. Using SST, remove the inner race from the steering knuckle.

      SST 09950-40011 (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

      Fig 6: Removing Inner Race From Steering Knuckle
      G02957812Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE FRONT AXLE HUB LH OIL SEAL 
    1. Using SST, remove the oil seal from the steering knuckle.

      SST 09308-00010

      Fig 7: Removing Oil Seal From Steering Knuckle
      G02957813Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE FRONT AXLE HUB LH HOLE SNAP RING 
    1. Using snap ring pliers, remove the snap ring.
  14. REMOVE FRONT AXLE HUB LH BEARING 
    1. Using SST and a press, press out the bearing from the steering knuckle.

      SST 09950-60010 (09951-00560)

      Fig 8: Pressing Out Bearing From Steering Knuckle
      G02957814Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL FRONT AXLE HUB LH BEARING 
    1. Using SST and a press, press in a new bearing to steering knuckle.

      SST 09309-36010, 09950-60020 (09951-00720), 09950-70010 (09951-07150)

      NOTE: If the inner race and balls come loose from the bearing outer race, make sure to install them in the same position as before. 
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.