Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Lexus SC 430FACTORY OEM SERVICE PROCEDURE
Torque Specification
TORQUE SPECIFICATIONS
| Part tightened | N.m | kgf.cm | ft.lbf |
|---|---|---|---|
| Starter | |||
| Terminal 30 nut, Terminal C nut x Terminal bolt | 17 | 173 | 13 |
| End cover x Magnetic switch housing | 3.6 | 37 | 32 in.lbf |
| End cover x Brush holder | 3.8 | 39 | 34 in.lbf |
| Starter housing x Magnetic switch | 9.3 | 95 | 82 in.lbf |
| End cover with starter yoke x Starter housing | 9.3 | 95 | 82 in.lbf |
| Lead wire of starter yoke x Terminal C | 5.9 | 60 | 52 in.lbf |
| Starter assy x Cylinder block | 37 | 380 | 27 |
| Starter cable x Starter assy | 9.8 | 100 | 87 in.lbf |
| Throttle body x Intake manifold | 18 | 185 | 13 |
| Generator | |||
| Bearing retainer x Drive end frame | 3.0 | 31 | 27 in.lbf |
| Generator pulley x Rotor | 110.5 | 1,125 | 82 |
| Lead wire (drive end frame) x Rectifier holder w/ rectifier | 2.94 | 30 | 26 in.lbf |
| Rectifier end frame x Drive end frame: w/Cord clip | 5.4 | 55 | 48in.lbf |
| Rectifier end frame x Drive end frame: w/o Cord clip | 4.5 | 46 | 40 in.lbf |
| Voltage regulator assy x Rectifier holder | 2.0 | 20 | 18 in.lbf |
| Brush holder assy x Rectifier holder, Voltage regulator | 2.0 | 20 | 18 in.lbf |
| Rear end cover x Rectifier end frame | 4.4 | 45 | 39 in.lbf |
| Plate terminal x Rectifier holder, Rectifier end frame | 3.8 | 39 | 34 in.lbf |
| Terminal insulator x Rectifier holder | 6.5 | 66 | 58 in.lbf |
| Generator x Cylinder block | 39 | 400 | 29 |
| Vane pump pulley x Vane pump | 43 | 440 | 32 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.
