2003 Lexus ES 300FACTORY OEM SERVICE PROCEDURE

Front Power Seat Control System: Inspection

  1. INSPECT FRONT POWER SEAT SWITCH LH 
    1. Inspect the continuity between each terminal when each switch is operated.

      Standard (Slide switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 9 (1) (4 <==> 6) FRONT Continuity
      (1) (6 <==> 4 <==> 9) OFF Continuity
      (1) (4 <==> 9) 1 <==> 6 REAR Continuity
      (1) Except memory seat.If the result is not as specified, replace the front power switch.

      Standard (Front vertical switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 5 4 <==> 10 UP Continuity
      (1) (5 <==> 4 <==> 10) OFF Continuity
      1 <==> 10 (1) (4 <==> 5) DOWN Continuity
      (1) Except memory seat.If the result is not as specified, replace the front power switch.

      Standard (Lifter switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 7 (1) (4 <==> 8) UP Continuity
      (1) (7 <==> 4 <==> 8) OFF Continuity
      1 <==> 8 (1) (4 <==> 7) DOWN Continuity
      (1) Except memory seat.If the result is not as specified, replace the front power switch.

      Standard (Reclining switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 3 (1)(2 <==> 4) FRONT Continuity
      (1) (2 <==> 4 <==> 3) OFF Continuity
      1 <==> 2 (1)(3 <==> 4) REAR Continuity
      (1) Except memory seat.If the result is not as specified, replace the front power switch.
      Fig 1: Identifying Front Power Seat Switch LH Connected Terminal
      G03373156Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT FRONT POWER SEAT SWITCH RH 
    1. Inspect the continuity between each terminal when each switch is operated.

      Standard (Slide switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 9 4 <==> 6 FRONT Continuity
      6 <==> 4 <==> 9 OFF Continuity
      4 <==> 9 1 <==> 6 REAR Continuity

      Standard (Front vertical switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 5 4 <==> 10 UP Continuity
      5 <==> 4 <==> 10 OFF Continuity
      1 <==> 10 4 <==> 5 DOWN Continuity

      Standard (Rear vertical switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 8 4 <==> 7 UP Continuity
      7 <==> 4 <==> 8 OFF Continuity
      1 <==> 7 4 <==> 8 DOWN Continuity

      Standard (Reclining switch): 

      TERMINAL SPECIFIED CONDITION

      Terminal No. Switch position Specified condition
      1 <==> 3 2 <==> 4 FRONT Continuity
      2 <==> 4 <==> 3 OFF Continuity
      1 <==> 2 3 <==> 4 REAR Continuity

      If the result is not as specified, replace the front power switch.

      Fig 2: Identifying Front Power Seat Switch RH Connected Terminal
      G03373157Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSPECT POWER SEAT FRONT LH SWITCH ASSY 
    1. Inspect the continuity between each terminal when each switch is operated.

      Standard: 

      TERMINAL SPECIFIED CONDITION

      Switch position Specified condition
      1 <==> 4 2 <==> 3 FRONT Continuity
      3 <==> 2 <==> 4 OFF Continuity
      1 <==> 3 2 <==> 4 REAR Continuity

      If the result is not as specified, replace the power seat switch.

      Fig 3: Identifying Power Seat Front LH Switch Assy
      G03373158Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.