2002 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Heater Control Panel Base Sub-Assembly Replacement (BO006-04)

Publication date: 2004-09-14
Reference number: BO006-04

HEATER CONTROL PANEL BASE SUB-ASSEMBLY REPLACEMENT

HEATER CONTROL PANEL BASE SUB-ASSEMBLY REPLACEMENT

TECHNICAL SERVICE BULLETIN

Reference Number(s): BO006-04, Date of Issue:  September 14, 2004
LEXUS: 2002 - 2004 SC 430
SECTION: BODY
COPYRIGHT: © 2018 Lexus, a division of Toyota Motor Sales, USA License Agreement TMS1002

INTRODUCTION

The heater control panel base sub-assembly can now be replaced without having to replace the complete Air Conditioner Control Assembly. This bulletin provides procedures for this repair.

APPLICABLE VEHICLES

2002 - 2004  model year SC 430  vehicles.

PARTS INFORMATION

PARTS INFORMATION

Previous Part Number Current Part Number Part Name Qty
N/A 55901-24020 Base Sub-assembly, Heater Control 1
N/A 55901-24030 Base Sub-assembly, Heater Control w/Electro Multi-vision 1

WARRANTY INFORMATION

WARRANTY INFORMATION

OP Code Description Time OFP T1 T2
BD4013 R & R A/C Control Base Sub-assembly 0.7 55902-24050 99 99
BD4013 R & R A/C Control Base Sub-assembly 0.7 55902-24060 99 99
NOTE: Applicable Warranty*
This repair is covered under the Lexus Comprehensive Warranty. This warranty is in effect for 48 months or 50,000 miles, whichever occurs first, from the vehicle's in-service date.

* Warranty application is limited to correction of a problem based upon a customer's specific complaint.

COMPONENTS

Fig 1: Heater Control Panel Base Sub-Assembly Components
G02538850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

REPAIR PROCEDURE

CAUTION:
  • Disconnect the negative battery terminal and wait at least 90 seconds BEFORE performing work.
  • When disassembling air conditioner control assembly, measures should be taken to prevent static electricity from damaging the system.
  1. Remove Air Conditioner Control Assembly. 
    1. Pull the air conditioner control assembly towards the rear of the vehicle and disengage the 6 clip fittings.
      Fig 2: Air Conditioner Control Assembly Clip Locations
      G02538851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the 3 connectors and remove the air conditioner control assembly.
  2. Remove Console Upper Panel Garnish Front. 
    1. Remove the 2 screws.
    2. Disengage the 2 claw fittings and remove the console upper panel garnish from the air conditioner control assembly.
    Fig 3: Removing Console Upper Panel Garnish Front
    G02538852Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. Remove Heater Control Housing. 
    1. Remove the 6 screws and disengage the 4 claw fittings. Then separate the heater control housing.
      Fig 4: Removing Heater Control Housing
      G02538853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the 2 cooler wires No. 1 and remove the heater control housing.
    Fig 5: Cooler Wires
    G02538854Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. Remove Cooler Wire No. 1 (w/Lexus Navigation System). 
    1. Disconnect the cooler wire No. 1 from the air conditioner panel.
    Fig 6: Cooler Wire No: 1
    G02538855Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. Remove Heater Control Base Sub-assembly. 
    1. Remove the 2 screws.
      Fig 7: Heater Control Base Sub-Assembly Screw Locations
      G02538856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a thin flathead screwdriver with the tip taped up with protective tape, disengage the 7 claw fittings in the order shown in Fig 8.
      NOTE: Bend the film (Black) forward to insert the flathead screwdriver from underneath the base into claw fittings (4) and (7) as shown in Fig 8 and then disengage these fittings.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.