2002 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Section 428 (Instrument Panel): Installation

WARNING: This page is about a different car, the 2003 Lexus LX 470. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL REINFORCEMENT 
  2. w/Night View: 

    INSTALL NIGHT VIEW BATTERY ECU 

    Install the night view battery ECU with the 2 screws.

  3. INSTALL NO. 1 BRACE 
  4. INSTALL FLOOR BRACE 
  5. INSTALL GLOVE COMPARTMENT DOOR DAMPER 
  6. INSTALL NO. 4 HEATER TO REGISTER DUCT 
  7. INSTALL NO. 3 HEATER TO REGISTER DUCT 
  8. INSTALL ECM (See  ENGINE CONTROL MODULE (ECM)  ) 
  9. INSTALL INSTRUMENT PANEL 

    HINT:

    • Install the airbag connector between the No. 5 heater to, register duct and the center bracket temporarily, then install the instrument panel.
    • Remove the airbag connector before installing the lower No. 2 panel.
    1. install the 6 bolts, the 2 nuts and the instrument panel, then connect the connectors.
    2. Install the 2 bolts to the front passenger airbag assembly.

      Torque: 20 N.m (204 kgf.cm, 15 ft.lbf) 

    3. Connect the junction connectors.

    HINT:

    The connectors can be connected by tightening the bolts.

  10. INSTALL TRANSCEIVER FINISH PLATE NO. 2 ASSEMBLY 
    Fig 1: Installing Airbag Connector Between No. 5 Heater To Register Duct & Center Bracket
    G03375916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. w/ Night View: 

    INSTALL NIGHT VIEW DISPLAY 

    Install the night view display with the 4 screws.

    Fig 2: Installing Night View Display - W/ Night View
    G03375917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. w/ Night View: 

    INSTALL NIGHT VIEW ECU 

    1. Connect the connectors to the night view ECU.
    2. Install the night view ECU with the 3 bolts.
    Fig 3: Installing Night View ECU - W/ Night View
    G03375918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL FRONT CONSOLE BOX AND CONSOLE BOX MOUNTING BRACKET NO. 4 

    Install the front console box and the console box mounting bracket No. 4 with the 4 bolts.

  14. INSTALL FRONT ASH RECEPTACLE RETAINER 
    1. Install the front ash receptacle retainer with the 2 screws.
    2. Install the front ash receptacle box.
    Fig 4: Installing Front Console Box & Console Box Mounting Bracket No. 4
    G03375919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL CENTER LOWER CLUSTER FINISH PANEL 

    Connect the connectors, then install the center lower cluster finish panel.

    Fig 5: Installing Center Lower Cluster Finish Panel
    G03375920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. w/(c) Disc Player Changer, LEXUS Link System: 

    INSTALL REAR CONSOLE BOX 

    Install the rear console box with the 4 bolts and the 4 screws.

    Fig 6: Installing Rear Console Box - W/(C) Disc Player Changer, Lexus Link System
    G03375921Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. w/ Disc Player Changer: 

    INSTALL REAR CONSOLE BOX 

    Install the rear console box with the 2 bolts and the 6 screws.

    Fig 7: Installing Rear Console Box - W/Disc Player Changer
    G03375922Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. w/LEXUS Link System: 

    INSTALL REAR CONSOLE BOX 

    Install the rear console box with the 2 nuts, the 6 screws.

  19. INSTALL REAR RADIO CONTROL PANEL 

    Install the rear radio control panel with the 3 screws, and connect the connector.

    Fig 8: Installing Rear Console Box - W/Lexus Link System
    G03375923Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. INSTALL CONSOLE REAR END PANEL 
    1. Install the console rear end panel with the 2 screws.
    2. Install the console cup holder box.
  21. INSTALL UPPER CONSOLE PANEL 

    Install the upper console panel, then install the transfer shift lever knob.

    Fig 9: Installing Console Rear End Panel
    G03375924Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. INSTALL RADIO WITH A/C CONTROL ASSEMBLY 

    Install the radio with A/C control with the 4 bolts.

    Fig 10: Installing Radio With A/C Control Assembly
    G03375925Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. INSTALL INSTRUMENT CLUSTER FINISH PANEL 

    Connect the connectors, then install the instrument cluster finish panel.

  24. INSTALL CENTER RESISTER 

    Install the center resister.

  25. INSTALL LOWER NO. 2 PANEL 

    Install the lower No. 2 panel with the 3 screws.

    Fig 11: Installing Instrument Cluster Finish Panel
    G03375926Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  26. CONNECT AIRBAG CONNECTOR (See  DISABLING & ACTIVATING AIR BAG SYSTEM  ) 
  27. INSTALL GLOVE COMPARTMENT DOOR 
    1. Connect the glove compartment door damper clip, then install the glove compartment door.
    2. Install the 2 screws.
    Fig 12: Installing Glove Compartment Door
    G03375927Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  28. INSTALL COMBINATION METER 
    1. Check that the set-in connectors are connected in the installation holes on the instrument panel securely.
    2. Place the combination meter on the instrument panel.
    3. Install the combination meter by tightening the screws, A, B and C in the order.
      Fig 13: Installing Combination Meter
      G03375928Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Tighten the connection bolts.

    HINT:

    • When the connection is completed, the bolts should turn vainly, causing turning noise.
    • Check that the connection check pins protrude from the lower side of the connection bolts.
    NOTE: Follow the procedures in the order of (c) and (d). Otherwise, the set-in connectors on the wire harness side and on the meter side might not be connected properly. 
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.