Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Section 420 (Power Seat Control System): Inspection
- INSPECT DRIVER'S POWER SEAT SWITCH CIRCUIT (See  POWER SEAT CONTROL SWITCH CIRCUIT )Â
- INSPECT PASSENGER'S POWER SEAT SWITCH CONTINUITYÂ
Slide switch:Â
SLIDE SWITCHSwitch position Tester connection Specified condition FRONT 4-7-(6) 8-11-(12) Continuity OFF 4-7-(6)-8 Continuity BACK 4-11-(12) (6)-7-8 Continuity Front vertical switch:Â
FRONT VERTICAL SWITCHSwitch position Tester connection Specified condition UP (6)-7-10 9-11-(12) Continuity OFF (6)-7-9-10 Continuity DOWN 6-(7)-9 10-11 - (12) Continuity Lifter switch:Â
LIFTER SWITCHSwitch position Tester connection Specified condition UP 2-(6)-7 3-11-(12) Continuity OFF 2-3-(6)-7 Continuity DOWN 2-11-(12) 3-(6)-7 Continuity Reclining switch:Â
RECLINING SWITCHSwitch position Tester connection Specified condition FORWARD 1-11-(12) 5-(6)-7 Continuity OFF 1 - 5 - (6) - 7 Continuity REAR 1-(6)-7 5-11-(12) Continuity If continuity is not as specified, replace the switch.
- INSPECT PASSENGER'S POWER SEAT SWITCH CIRCUITÂ
- Disconnect the switch connector and connect the seat wire harness to the floor wire harness.
- Inspect the connector on the wire harness side.
SPECIFIED CONDITIONTester connection Condition Specified condition 7 - Ground Always Continuity 11 -Ground Always Battery positive voltage If circuit is not as specified, inspect the circuits connected to other parts.
- INSPECT DRIVER'S LUMBAR SUPPORT SWITCH CONTINUITYÂ SPECIFIED CONDITION
Switch position Tester connection Specified condition FORWARD 1-4
2-3Continuity OFF 1-2-3 Continuity RELEASE 1-3
2-4Continuity If continuity is not as specified, replace the switch.
- INSPECT DRIVER'S LUMBAR SUPPORT SWITCH CIRCUITÂ
- Disconnect the switch connector and connect the seat wire harness to the floor wire harness.
- Inspect the connector on the wire harness side.
SPECIFIED CONDITIONTester connection Condition Specified condition 3 - Ground Always Continuity 4 - Ground Always Battery positive voltage If circuit is not as specified, inspect the circuits connected to other parts.
- INSPECT SLIDE MOTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, check that the motor turns clockwise.
- Reverse the polarity, and check that the motor turns counterclockwise.
If operation is not as specified, replace the seat adjuster.
- INSPECT SLIDE MOTOR PTC THERMISTOR OPERATIONÂ
(): Passenger sideÂ
- Connect the battery positive (+) lead to terminal 2(1), the ammeter positive (+) lead to terminal 1 (2) and the ammeter negative (-) lead to the battery negative (-) terminal, then move the seat cushion to the front position.
- Continue to apply voltage, and check that current changes to less than 1 ampere within 4 to 90 seconds.
- Disconnect the leads from terminals.
- Approximately 60 seconds later, connect the battery positive (+) lead to terminal 1 (2) and the battery negative (-) lead to terminal 2 (1), and check that the seat cushion begins to move backwards.
If operation is not as specified, replace the seat adjuster.
- INSPECT FRONT VERTICAL MOTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, and check that the motor turns clockwise.
- Reverse the polarity, and check that the motor turns counterclockwise.
If operation is not as specified, replace the seat adjuster.
- INSPECT FRONT VERTICAL MOTOR PTC THERMISTOR OPERATIONÂ
(): Passenger sideÂ
- Connect the battery positive (+) lead to terminal 1 (2), the ammeter positive (+) lead to terminal 2 (1) and the ammeter negative (-) lead to the battery negative (-) terminal, then move the seat cushion to the highest position.
- Continue to apply voltage, and check that the current changes to less than 1 ampere within 4 to 90 seconds.
- Disconnect the leads from the terminals.
- Approximately 60 seconds later, connect the battery positive (+) lead to terminal 2 (1) and the battery negative (-) lead to terminal 1 (2), and check that the seat cushion begins to descend.
If operation is not as specified, replace the seat adjuster.
- INSPECT LIFTER MOTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, and check that the motor turns clockwise.
- Reverse the polarity, and check that the motor turns counterclockwise.
If operation is not as specified, replace the seat adjuster.
- INSPECT LIFTER MOTOR PTC THERMISTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 (2), the ammeter positive (+) lead to terminal 2 (1) and the ammeter negative (-) lead to the battery negative (-) terminal, then move the seat to the highest position.
- Continue to apply voltage, and check that the current changes to less than 1 ampere within 4 to 90 seconds.
- Disconnect the leads from the terminals.
- Approximately 60 seconds later, connect the battery positive (+) lead to terminal 2 (1) and the battery negative (-) lead to terminal 1 (2), and check that the seat begins to descend.
If operation is not as specified, replace the seat adjuster.
- INSPECT RECLINING MOTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, and check that the motor turns clockwise.
- Reverse the polarity, and check that the motor turns counterclockwise.
If operation is not as specified, replace the seat adjuster.
- INSPECT RECLINING MOTOR PTC THERMISTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 2, the ammeter positive (+) lead to terminal 1 and the ammeter negative (-) lead to the battery negative (-) terminal, then recline the seat back to the most forward position.
- Continue to apply voltage, and check that the current changes to less than 1 ampere within 4 to 90 seconds.
- Disconnect the leads from the terminals.
- Approximately 60 seconds later, connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, and check that the seat back begins to fall backward.
If operation is not as specified, replace the seat adjuster.
- INSPECT LUMBAR SUPPORT MOTOR OPERATIONÂ
- Connect the battery positive (+) lead to terminal 1 and the battery negative (-) lead to terminal 2, and check that the lumbar support moves to release side.
- Reverse the polarity, check that the lumbar support moves forward.
if operation is not as specified, replace the seat adjuster.
- INSPECT LUMBAR SUPPORT MOTOR CIRCUIT BREAKER OPERATION
- Connect the battery positive (+) lead to terminal 2 and the battery negative (-) lead to terminal 1 on the lumbar support motor connector and move the lumbar support to front end position.
- Continue to apply voltage, and check that a circuit breaker operation noise can be heard within 4 to 60 seconds.
- Reverse the polarity, check that the lumbar support begins to move to the release side within approximately 60 seconds.
If operation is not as specified, replace the motor.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
