Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Lexus SC 430FACTORY OEM SERVICE PROCEDURE
Torque Specification
WARNING: This page is about a different car, the 2003 Lexus LX 470. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATION
| Part tightened | N.m | kgf.cm | ft.lbf | |
|---|---|---|---|---|
| No.1 vehicle speed sensor x Transfer case | 16 | 160 | 12 | |
| No.2 vehicle speed sensor x Transmission case | NT | 5.4 | 55 | 48 in..lbf |
| SP2 | 5.4 | 55 | 48 in..lbf | |
| ATF temperature sensor (for linear control) x Valve body | 11 | 112 | 8 | |
| ATF temperature sensor (for oil temp warning lamp) x Valve body | 10 | 100 | 7 | |
| ATF temperature sensor x Transmission case | 5.4 | 55 | 48 in..lbf | |
| Park/neutral position switch | Bolt | 13 | 130 | 9 |
| Nut | 3.9 | 40 | 35 in..bf | |
| Transmission control shaft lever x Transmission control rod | 13 | 130 | 9 | |
| Shift solenoid lock plate x Valve body | 6.4 | 65 | 57 in..lbf | |
| Shift solenoid S1 S2 x Valve body | 10 | 102 | 7 | |
| Shift solenoid SR x Valve body | 6.4 | 65 | 57 in..lbf | |
| Valve body x Transmission case | 11 | 110 | 8 | |
| Oil stainer x Valve body | 10 | 100 | 7 | |
| Oil pan x Transmission case | 4.4 | 55 | 39 in..lbf | |
| Drain plug x Oil pan | 20 | 205 | 15 | |
| Parking lock pawl bracket x Transmission case | 7.4 | 75 | 65 in..lbf | |
| Shift lever assembly x Body | 8.3 | 85 | 73 in..lbf | |
| Control lever x Shift lever plate | 13 | 130 | 9 | |
| Transmission control rod x Shift lever assembly | 13 | 130 | 9 | |
| Shift lever guide housing x Shift lever plate | 4.9 | 50 | 43 in..lbf | |
| Power steering oil cooler sub-assy x Body | 7.5 | 76 | 66 in..lbf | |
| Oil cooler bracket x Body | 12 | 117 | 8 | |
| Oil cooler bracket x Oil cooler | 4.9 | 50 | 43 in..lbf | |
| Oil cooler pipe x Body | 4.9 | 50 | 43 in..lbf | |
| Oil filler pipe | 12 | 122 | 9 | |
| Engine No. 1 and No. 2 under cover x Body | 29 | 296 | 21 | |
| Transfer shift lever x Transfer shift lever rod assembly | 12 | 122 | 9 | |
| Transfer shift lever boot x Body | 5.4 | 55 | 48 in..lbf | |
| Hole plug x Transmission housing | 18 | 185 | 13 | |
| Drive plate x Torque converter clutch | 48 | 490 | 35 | |
| Oil cooler pipe union nut | 34 | 347 | 25 | |
| Crossmember | Bolt | 50 | 510 | 37 |
| Nut | 74 | 750 | 54 | |
| Engine mounting insulator rear x Transmission case | 59 | 600 | 43 | |
| Transmission housing x Engine | Bolt A | 71 | 724 | 52 |
| Bolt B | 37 | 377 | 27 | |
| Drive plate x Crankshaft | 1st | 49 | 500 | 36 |
| 2nd | Turn 90Β° | Turn 90Β° | Turn 90Β° | |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
