2002 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Service Data

WARNING: This page is about a different car, the 2003 Lexus LX 470. However, it is still accessible from the selected car via links, so may be relevant.
SERVICE DATA

A750F
Line pressure (Wheel locked) Engine idling
D position 362 - 420 kPa (3.7 - 4.3 kgf.cm2 , 53 - 61 psi)
R position 483 - 561 kPa (4.9 - 5.7 kgf.cm2 , 70 - 81 psi)
AT stall (Throttle valve fully opened)
D position 1,325 -1,423 kPa (13.5 - 14.5 kgf.cm2 ,192 - 206 psi)
R position 1,608 - 1,746 kPa (16.3 - 17.8 kgf.cm2 , 232 - 253 psi)
Engine stall revolution D and R positions 2,150 +/- 150 rpm
Time lag N --> D position Less than 0.7 seconds
N --> R position Less than 1.2 seconds
Engine idle speed (A/C OFF) N position 700 +/- 50 rpm
Drive plate runout Max. 0.20 mm (0.0079 in.)
Torque converter runout Max. 0.30 mm (0.0118 in.)
Torque converter clutch installation distance More than 17.1 mm (0.673 in.)
Shift schedule
D position
(Throttle valve fully opened) 1 --> 2 45 - 57 km/h (28 - 35 mph)
2-->3 79-90 km/h(49-56 mph)
3-->4 113 - 128 km/h (70 - 80 mph)
4-->5 165-180 km/h (103-112 mph)
5 --> 4 158 - 173 km/h (98 - 108 mph)
4-->3 105 - 117 km/h (65 - 73 mph)
3-->2 70-78 km/h (43-48 mph)
2-->1 35-41 km/h (22-25 mph)
(Throttle valve fully closed) 4-->5 46 - 53 km/h (29 - 33 mph)
5-->4 24-29 km/h (15-18 mph)
3 position
(Throttle valve fully opened) 1 --> 2 45 - 57 km/h (28 - 35 mph)
2-->3 79-90 km/h (49-56 mph)
4-->3 119-132 km/h (74-82 mph)
3-->2 70-78 km/h (43-48 mph)
2-->1 35-41 km/h (22-25 mph)
2 position
(Throttle valve fully opened) 1 --> 2 45-57 km/h (28-35 mph)
3-->2 80-88 km/h (50-55 mph)
2-->1 35-41 km/h (22-25 mph)
L position
(Throttle valve fully opened) 2-->1 43-50 km/h (27-31 mph)
Lock-up point Throttle valve opening 5 % Β 
D position
5th gear Lock-up ON 67-74 km/h (42-46 mph)
Lock-up OFF 60 - 67 km/h (37 - 42 mph)
4 position
4th gear Lock-up ON 61-68 km/h (38-42 mph)
Lock-up OFF 54-61 km/h (34-38 mph)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.