2002 Lexus SC 430FACTORY OEM SERVICE PROCEDURE

Timing Belt: Replacement

  1. SEPARATE BATTERY NEGATIVE TERMINAL 
  2. REMOVE AIR CLEANER INLET NO. 1 
  3. DRAIN ENGINE COOLANT 
  4. REMOVE V-BANK COVER 
  5. REMOVE INTAKE AIR CONNECTOR PIPE 
  6. REMOVE ENGINE UNDER COVER 
  7. SEPARATE RADIATOR HOSE NO. 1 
  8. SEPARATE RADIATOR HOSE NO. 2 
  9. SEPARATE OIL COOLER INLET TUBE NO. 1 
  10. SEPARATE OIL COOLER OUTLET TUBE NO. 1 
  11. REMOVE AIR CLEANER ASSY 
  12. REMOVE RADIATOR ASSY 
    1. Remove the 2 nuts and 2 upper radiator support.
    2. Lift out the radiator and cooling fan assembly.
  13. REMOVE FAN AND GENERATOR V BELT 

    (See  REPLACEMENT  ) 

  14. REMOVE VANE PUMP ASSY 
    1. Remove the 2 bolts and nut, and the vane pump assembly.
    NOTE: Vane pump assembly should be removed with the hoses connected and then hung with a rope or wire in the body's side.
  15. REMOVE GENERATOR ASSY 

    (See  REPLACEMENT  ) 

  16. SEPARATE COMPRESSOR AND MAGNETIC CLUTCH 
    NOTE: The cooler compressor together with the magnetic clutch should be removed with the low-pressure and high-pressure hoses connected and then hung with a rope or wire in the body's side.
  17. REMOVE TIMING CHAIN OR BELT COVER NO. 2 
  18. REMOVE TIMING BELT COVER SUB-ASSY NO. 3 LH 
  19. REMOVE TIMING BELT COVER SUB-ASSY NO. 2 
  20. REMOVE V-RIBBED BELT TENSIONER ASSY 
  21. REMOVE IDLER PULLEY ASSY 
  22. REMOVE CRANKSHAFT DAMPER SUB-ASSY 
    1. Using SST, remove the pulley bolt.

      SST 09213-70011, 09330-00021

      Fig 1: Removing Crankshaft Damper Pulley Bolt
      G03387534Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using SST, remove the crankshaft pulley.

      SST 09950-50012 (09951-05010, 09952-05010, 09953-05010,09953-05020, 09954-05020)

    Fig 2: Removing Crankshaft Pulley
    G03387535Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  23. REMOVE TIMING BELT NO. 1 COVER 
    1. Remove the 4 bolts and timing belt cover.
  24. REMOVE CRANKSHAFT POSITION SENSOR PLATE NO. 1 
  25. REMOVE TIMING BELT 
    1. If re-using the timing belt, check the installation marks on the timing belt.
      1. Check that there are 3 installation marks on the timing belt by turning the crankshaft as shown in the illustration.

      If the installation marks have disappeared, place a new installation mark on the timing belt before removing each part.

      Fig 3: Identifying Timing Belt Alignment Marks
      G03387536Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Set the No. 1 cylinder to approx. 50° BTDC/compression.
      1. Using the crankshaft damper bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.
        Fig 4: Aligning Crankshaft Pulley Timing Marks With Oil Pump Body
        G03387537Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Check that the timing marks of the camshaft timing pulleys and timing belt plates aligned.

        If not, turn the crankshaft 1 revolution (360°).

        Fig 5: Aligning Camshaft Pulleys With Timing Belt Plate Timing Marks
        G03387538Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Using the crankshaft damper bolt, turn the crankshaft counterclockwise by approx. 50°.
      NOTE: If the timing belt is disengaged, having the crankshaft pulley at the wrong angle can cause the piston head and valve head to come into contact with each other when you remove the camshaft timing pulley and camshaft, causing damage. So always set the crankshaft pulley at the correct angle.
    3. Alternately loosen the 2 bolts, and remove them, the belt tensioner and dust boot.
      Fig 6: Turning Crankshaft Counterclockwise
      G03387539Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using SST, loosen the tension between the camshaft timing pulley (RH bank) and crankshaft timing pulley by slightly turning the camshaft timing pulley (RH bank) counterclockwise.

      ST09960-10010 (09962-01000, 09963-00350)

      Fig 7: Using SST To Release Tension Between Camshaft Timing Pulley (RH Bank) & Crankshaft Timing Pulley
      G03387540Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the timing belt from the timing belt idler No. 1, and remove the timing belt.
  26. INSTALL TIMING BELT 
    1. Check the timing belt idler No. 1 and No. 2.
      1. Visually check the seal portion of the idler pulley for oil leakage.

        If leakage is found, replace the idler.

      2. Check that the idler turns smoothly.

        If necessary, replace the idler.

    2. Check the water pump.
      1. Visually check the air hole and water hole for coolant leakage.

        If leakage is found, replace the water pump and timing belt.

      2. Turn the pulley, and check that the water pump bearing moves smoothly and quietly.

        If necessary, replace the water pump.

    3. Remove any oil or water on the crankshaft pulley, oil pump pulley, water pump pulley, idler No.1 and idler No.2, and keep them clean.
      NOTE: Only wipe the pulleys; do not use any cleansing agent.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.