2002 Lexus ES 300FACTORY OEM SERVICE PROCEDURE

Frame Wire: Replacement

WARNING: This page is about a different car, the 2004 Toyota Prius. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
  • When working on the high voltage systems, always wear insulating gloves.
  • After removing the service plug grip, do not operate the power switch as it may damage the hybrid vehicle control ECU.
  • Keep the removed service plug in your pocket to prevent other technicians from reconnecting it while you are servicing the vehicle.
  • After removing the service plug grip, do not touch the high voltage connectors and terminals for 5 minutes.
  1. PRECAUTION (See  PRECAUTION  ) 
  2. REMOVE FRONT WHEELS 
  3. REMOVE REAR FLOOR BOARD NO. 2 (See  SERVICE PLUG GRIP  ) 
  4. REMOVE DECK FLOOR BOX REAR (See  SERVICE PLUG GRIP  ) 
  5. REMOVE REAR FLOOR BOARD NO. 3 (See  SERVICE PLUG GRIP  ) 
  6. DISCONNECT BATTERY NEGATIVE TERMINAL (See  SERVICE PLUG GRIP  ) 
  7. REMOVE SERVICE PLUG GRIP (See  SERVICE PLUG GRIP  ) 
  8. REMOVE DECK TRIM COVER REAR (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  9. REMOVE TONNEAU COVER ASSY (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  10. REMOVE REAR SEAT CUSHION ASSY (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  11. REMOVE REAR FLOOR BOARD NO. 1 (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  12. REMOVE REAR SIDE SEAT BACK FRAME LH (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  13. REMOVE REAR FLOOR BOARD NO. 4 (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  14. REMOVE DECK FLOOR BOX LH (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  15. REMOVE DECK TRIM SIDE PANEL ASSY LH (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  16. REMOVE BATTERY CARRIER BRACKET (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
  17. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Remove the clip and 4 joints shown in the illustration, then remove the rear door scuff plate.
      Fig 1: Removing Rear Door Scuff Plate LH
      G00950663Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. REMOVE FLOOR SIDE PANEL LH 
    1. Remove the clip, then roll back the carpet.
      Fig 2: Removing Carpet Clips
      G00950664Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the clip from the floor side panel.
    3. Remove the 3 bolts and floor side panel.
      Fig 3: Removing Clip From Floor Side Panel
      G00950665Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE BATTERY CARRIER PANEL NO. 6 (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
    NOTE: Wear insulating gloves.
  20. REMOVE JUNCTION TERMINAL (See  REMOVAL & INSTALLATION AND DISASSEMBLY & REASSEMBLY  ) 
    NOTE: Wear insulating gloves.
  21. REMOVE FRAME WIRE (RR POSITION) 
    NOTE: Wear insulating gloves.
    1. Remove the 2 nuts, then remove the frame wire from the system main relay No. 2 and No. 3.
      NOTE: Insulate the removed terminals with insulating tape.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.