2000 Lexus LX 470FACTORY OEM SERVICE PROCEDURE

Wheel Alignment Specifications: Tundra-Toe-In

WHEEL ALIGNMENT SPECIFICATIONS (TUNDRA-TOE-IN)

Application Specification
2WD
3.4L A/T
Regular Cab (1) 07' +- 12' (.12° +- .2°)
(2) .07 +- .08 (1.7 +- 2)
Extended Cab
Limited (1) 08' +- 12' (.13° +- .2°)
(2) .07 +- .08 (1.8 +- 2)
SR5
P245/70R16 (1) 09' +- 12' (.15° +- .2°)
(2) .08 +- .08 (2.0 +- 2)
P265/70R16 (1) 08' +- 12' (.14° +- .2°)
(2) .07 +- .08 (1.9 +- 2)
3.4L M/T
Extended Cab
SR5
P245/70R16 (1) 10' +- 12' (.16° +- .2°)
(2) .08 +- .08 (2.1 +- 2)
P265/70R16 (1) 09' +- 12' (.15° +- .2°)
(2) .08 +- .08 (2.0 +- 2)
Regular Cab (1) 08' +- 12' (.14° +- .2°)
(2) .07 +- .08 (1.8 +- 2)
4.7L A/T
Extended Cab
Limited (1) 06' +- 12' (.10° +- .2°)
(2) .05 +- .08 (1.4 +- 2)
SR5
P245/70R16 (1) 7' +- 12' (.12° +- .2°)
(2) .06 +- .08 (1.6 +- 2)
P265/70R16 (1) 07' +- 12' (.11° +- .2°)
(2) .08 +- .08 (1.5 +- 2)
4WD
3.4L A/T
Regular Cab
SR5
P245/70R16 & P265/70R16 (1) 6' +- 12' (.10° +- .2°)
(2) .05 +- .08 (1.4 +- 2)
Extended Cab
Limited & Off-Road Option (1) 7' +- 12' (.11° +- .2°)
(2) .06 +- .08 (1.5 +- 2)
SR5
P245/70R16 (1) 7 '+- 12 '(.12° +- .2°)
(2) .07 +- .08 (1.7 +- 2)
P265/70R16 (1) 08' +- 12' (.13° +- .2°)
(2) .07 +- .08 (1.7 +- 2)
Off-Road Option (1) 7' +- 12' (.12° +- .2°)
(2) .06 +- .08 (1.6 +- 2)
3.4L M/T
Regular Cab
SR5
P245/70R16 & P265/70R16 (1) 7' +- 12' (.11° +- .2°)
(2) .06 +- .08 (15 +- 2)
Extended Cab
SR5
P245/70R16 (1) 8' +- 12' (.13° +- .2°)
(2) .07 +- .08 (1.8 +- 2)
P265/70R16 (1) 08' +- 12' (.14° +- .2°)
(2) .07 +- .08 (1.8 +- 2)
Off-Road Option (1)8' +- 12' (.13° +- .2°)
(2) .07 +- .08 (1.7 +- 2)
4.7L A/T
Regular Cab
P245/70R16 (1) 4' +- 12' (.07° +- .2°)
(2) .04 +- .08 (1.0 +- 2)
P265/70R16 (1) 4' +- 12' (.07° +- .2°)
(2) .04 +- .08 (.9 +- 2)
Extended Cab
Limited & Off-Road Option (1) 5' +- 12' (.08° +- .2°)
(2) .04 +- .08 (1.1 +- 2)
4.7L A/T
Extended Cab
SR5
P245/70R16 (1) 5' +- 12' (.09° +- .2°)
(2) .05 +- .08 (1.3 +- 2)
P265/70R16 (1) 06' +- 12' (.10° +- .2°)
(2) .05' +- .08' (1.3 +- 2)
Off-Road Option (1) 5' +- 12' (.09° +- .2°)
(2) .05 +- .08 (1.2 +- 2)
(1) Measurement in 0 degrees, minutes (decimal degrees).
(2) Measurement in inches (mm).
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.