2000 Lexus LS 400FACTORY OEM SERVICE PROCEDURE

Shift Lock Solenoid

  1. Access shift lock ECU. See Figure and Figure . Turn ignition switch to ON position. Using DVOM, measure voltage by backprobing between specified shift lock ECU terminals with vehicle operated under specified condition. See SHIFT LOCK SOLENOID PIN VOLTAGES  table. Ensure voltage is as specified. For connector terminal identification, see CONNECTOR IDENTIFICATION .
    NOTE: On Avalon (floor shift), Celica, Corolla, ES300, GS300, GS400, RAV4 and RX300; shift lock solenoid is incorporated with shift lock ECU. Voltage tests for shift lock solenoid circuits are not available.
  2. Disconnect electrical connector from shift lock solenoid. Using DVOM, measure resistance between shift lock solenoid terminals. See SHIFT LOCK SOLENOID RESISTANCE SPECIFICATIONS  table. If shift lock solenoid resistance is not within specification, replace shift lock solenoid. If shift lock solenoid resistance is within specification, go to next step.
  3. Connect jumper wire between positive battery terminal and appropriate shift lock solenoid terminal. Connect an additional jumper wire between ground and appropriate shift lock solenoid terminal. Replace shift lock solenoid if operating sound cannot be heard.
SHIFT LOCK SOLENOID PIN VOLTAGES

Application & Terminal No. Condition Voltage
Avalon
1 & 2 Ignition Switch In ACC Position, Shifter In "P" Position 0
1 & 2 Brake Pedal Depressed 8.5-13.5
1 & 2 Ignition Switch In ACC Position, Shifter Not In "P" Position 0
Camry, Camry Solara, Land Cruiser, LX470 & Tacoma
2 & 5 Ignition Switch In ON Position, Shifter In "P" Position 0
2 & 5 Brake Pedal Depressed 8.5-13.5
2 & 5 Ignition Switch In ON Position, Shifter Not In "P" Position 0
ECHO
1 & 2 Ignition Switch In ON Position, Shifter In "P" Position 0
1 & 2 Brake Pedal Depressed 10-14
1 & 2 Ignition Switch In ON Position, Shifter Not In "P" Position 0
LS400
3 & 6 Ignition Switch In ON Position, Shifter In "P" Position 0
3 & 6 Ignition Switch In ON Position, Brake Pedal Depressed 8.8-12.5
3 & 6 Ignition Switch In ON Position, Brake Pedal Depressed (After 20 Seconds) 6.5-9.2
3 & 6 Ignition Switch In ON Position, Shifter In "D", "3", "2" & "L" Position 0
SC300 & SC400
3 & 6 Ignition Switch In ON Position, Shifter In "P" Position 0
3 & 6 Ignition Switch In ON Position, Brake Pedal Depressed 8.0-12.5
3 & 6 Ignition Switch In ON Position, Brake Pedal Depressed (After 20 Seconds) 6.5-9.2
3 & 6 Ignition Switch In ON Position, Shifter In "D", "4", "3", "2" & "L" Position 0
4Runner
2 & 5 Ignition Switch In ON Position, Shifter In "P" Position 0
2 & 5 Ignition Switch In ON Position, Brake Pedal Depressed 8.5-13.5
2 & 5 Ignition Switch In ON Position, Brake Pedal Depressed (After 20 Seconds) 6-8.5
2 & 5 Ignition Switch In ON Position, Shifter Not In "P" Position 0
SHIFT LOCK SOLENOID RESISTANCE SPECIFICATIONS

Application Ohms
Avalon (Column Shift Only), Camry & Camry Solara 29-35
ECHO (1)
4Runner 21-27
Land Cruiser, LS400, LX470, SC300, SC400 & Tacoma 20-28
(1) Information is not available.
Chapter Navigation
Return to Chapter: Component Tests
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.