Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Lexus SC 400FACTORY OEM SERVICE PROCEDURE
Specifications Index
SC300 & SC400 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||||
|---|---|---|---|---|---|
| Air Conditioning | |||||
| Service | A/C-HEATER SYSTEMS SPECIFICATIONS | ||||
| Torque | TORQUE SPECIFICATIONS | ||||
| Axle Shaft/Bearing Lock Nut/Drive Axle Nut | |||||
| Front | |||||
| Axle Hub Lock Nut | N/A | ||||
| Rear | |||||
| Drive Axle Lock Nut | 213 Ft.lbs (289 N.m) | ||||
| Battery | Β | ||||
| SC300 | BATTERY | ||||
| SC400 | BATTERY | ||||
| Brakes | |||||
| Bleeding Sequence | |||||
| SC300 | BLEEDING BRAKE SYSTEM | ||||
| SC400 | BLEEDING BRAKE SYSTEM | ||||
| Disc Brakes | |||||
| SC300 | DISC BRAKE SPECIFICATIONS | ||||
| SC400 | DISC BRAKE SPECIFICATIONS | ||||
| Torque | |||||
| SC300 | TORQUE SPECIFICATIONS | ||||
| SC400 | TORQUE SPECIFICATIONS | ||||
| Charging | |||||
| Generator | |||||
| SC300 & SC400 | ON-VEHICLE TESTING | ||||
| Torque | SPECIFICATIONS | ||||
| Drive Belts | |||||
| Adjustment | |||||
| SC300 | BELT ADJUSTMENT | ||||
| SC400 | BELT ADJUSTMENT | ||||
| Belt Routing | DESCRIPTION & OPERATION | ||||
| Engine Cooling | |||||
| General Service Specifications | |||||
| SC300 | COOLING SYSTEM SPECIFICATIONS | ||||
| SC400 | COOLING SYSTEM SPECIFICATIONS | ||||
| Radiator Cap Pressure | 10.7 psi | ||||
| Thermostat R & I | |||||
| SC300 | THERMOSTAT | ||||
| SC400 | THERMOSTAT | ||||
| Water Pump R & I | |||||
| SC300 | WATER PUMP | ||||
| SC400 | WATER PUMP | ||||
| Engine Mechanical | |||||
| Compression | |||||
| SC30 | ENGINE COMPRESSION | ||||
| SC400 | ENGINE COMPRESSION | ||||
| Oil Pressure | |||||
| SC300 | At least 7.1 psi (0.5 kg/cm2 ) at idle and about 47-84 psi (3.3-5.9 kg/cm2 ) at 3000 RPM | ||||
| SC400 | At least 4.3 psi (0.3 kg/cm2 ) at idle and 43-85 psi (3.0-6.0 kg/cm2 ) at 3000 RPM | ||||
| Overhaul | |||||
| SC300 | ENGINE SPECIFICATIONS | ||||
| SC400 | GENERAL ENGINE SPECIFICATIONS | ||||
| Torque | |||||
| SC300 | TORQUE SPECIFICATIONS | ||||
| SC400 | TORQUE SPECIFICATIONS | ||||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||||
| Flywheel/Flex Plate (Drive Plate) Torque | |||||
| Drive Plate-To-Crankshaft | |||||
| SC300 | |||||
| AT | 61 Ft.lbs (83 N.m) | ||||
| MT | |||||
| Step 1 | 36 Ft.lbs (49 N.m) | ||||
| Step 2 | Additional 90 Degrees | ||||
| SC400 | 61 Ft.lbs (83 N.m) | ||||
| Fuel System | |||||
| Pressure Specification | |||||
| SC300 & SC400 | 28-34 psi (2.0-2.4 kg/cm2 ) | ||||
| Fuel Pressure Test Procedure | |||||
| SC300 | FUEL PRESSURE | ||||
| SC400 | FUEL PRESSURE | ||||
| Fuel Filter | |||||
| SC300 | FUEL PUMP | ||||
| SC400 | FUEL PUMP | ||||
| Ignition | |||||
| Firing Order & Cylinder Identification | |||||
| SC300 | FIRING ORDER & CYLINDER NUMBERING | ||||
| SC400 | FIRING ORDER & CYLINDER NUMBERING | ||||
| Ignition Wires (Resistance) | |||||
| SC300 | HIGH TENSION WIRE RESISTANCE | ||||
| SC400 | HIGH TENSION WIRE RESISTANCE | ||||
| Ignition Wires (Routing) | |||||
| SC300 | FIRING ORDER & CYLINDER NUMBERING | ||||
| SC400 | See "Installing Spark Plug Wires & Retaining Brackets" figure under VALVE CLEARANCE ADJUSTMENT | ||||
| Spark Plugs | |||||
| SC300 | |||||
| Type | NGK No. BKR5EP-11 | ||||
| Gap | .043 In. (1.10 mm) | ||||
| Torque | 13 Ft. lbs (17 N.m) | ||||
| SC400 | |||||
| Type | NGK No. BKR6EP-11 | ||||
| Gap | .043 In. (1.10 mm) | ||||
| Torque | 13 Ft. lbs (17 N.m) | ||||
| Starting | |||||
| Starter | |||||
| SC300 | OVERHAUL | ||||
| SC400 | OVERHAUL | ||||
| Torque | |||||
| SC300 | TORQUE SPECIFICATIONS | ||||
| SC400 | TORQUE SPECIFICATIONS | ||||
| Wheel Alignment | |||||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||||
| Torque | TORQUE SPECIFICATIONS | ||||
| Wheel & Tire | |||||
| Wheel Lug Nut Torque | 76 Ft.lbs (103 N.m) | ||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
