Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Land Rover Range Rover BaseFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code Index DTC: Adaptive Speed Control Module (ASCM) -- Range Rover/L405
- General Information
- Description And Operation
- Diagnostic Trouble Code Index - DTC: Adaptive Speed Control Module (ASCM) (G2391130)
- Adaptive Cruise Control Module (ASCM)
- DTC C0078-61: Tire Diameter - Signal calculation failure
- DTC C1A67-25: Forward Looking Sensor - Signal shape/waveform failure
- DTC C1A67-54: Forward Looking Sensor - Missing calibration
- DTC C1A67-78: Forward Looking Sensor - Alignment or adjustment incorrect
- DTC C1A67-97: Forward Looking Sensor - Component or system operation obstructed or blocked
- DTC U0046-55: Vehicle Communication Bus C - Not configured
- DTC U0046-81: Vehicle Communication Bus C - Invalid serial data received
- DTC U0046-82: Vehicle Communication Bus C - Alive/sequence counter incorrect/not updated
- DTC U0046-83: Vehicle Communication Bus C - Value of signal protection calculation incorrect
- DTC U0046-87: Vehicle Communication Bus C - Missing message
- DTC U0046-88: Vehicle Communication Bus C - Bus off
- DTC U0300-00: Internal Control Module Software Incompatibility - No sub type information
- DTC U0300-56: Internal Control Module Software Incompatibility - Invalid/incomplete configuration
- DTC U0305-00: Software Incompatibility with Cruise Control Module - No sub type information
- DTC U0305-54: Software Incompatibility with Cruise Control Module - Missing calibration
- DTC U1A00-81: Private Communication Network - Invalid serial data received
- DTC U1A00-82: Private Communication Network - Alive/sequence counter incorrect/not updated
- DTC U1A00-83: Private Communication Network - Value of signal protection calculation incorrect
- DTC U1A00-87: Private Communication Network - Missing message
- DTC U2108-67: Adaptive Cruise Control - Signal incorrect after event
- DTC U2300-54: Central Configuration - Missing calibration
- DTC U2300-55: Central Configuration - Not configured
- DTC U2300-56: Central Configuration - Invalid/incomplete configuration
- DTC U2300-64: Central Configuration - Signal plausibility failure
- DTC U3000-19: Control Module - Circuit current above threshold
- DTC U3000-49: Control Module - Internal electronic failure
- DTC U3000-53: Control Module - Deactivated
- DTC U3000-63: Control Module - Circuit/component protection time-out
- DTC U3000-67: Control Module - Signal incorrect after event
- DTC U3000-92: Control Module - Performance or incorrect operation
- DTC U3000-93: Control Module - No operation
- DTC U3000-94: Control Module - Unexpected operation
- DTC U3000-98: Control Module - Component or system over temperature
- DTC U3006-17: Control Module Input Power "A" - Circuit voltage above threshold
- DTC U3006-19: Control Module Input Power "A" - Circuit current above threshold
- Diagnostic Trouble Code Index - DTC: Adaptive Speed Control Module (ASCM) (G2391130)
- Description And Operation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
