Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Land Rover LR2 (LF) L6-3.2LFACTORY OEM SERVICE PROCEDURE
Engine Controls - MIL ON/DTC's P0172/P0175 Set
No: LTB00377 (Issue 1)
25 MAY 2011
SECTION: 303
Engine MIL Illuminated with DTC P01721 / P0175 Stored
AFFECTED VEHICLE RANGE:
LR2 (LF) VIN: 8H000212 - BH252720
Model Year: 2008 - 2011
CONDITION SUMMARY:
Situation:
The engine Malfunction Indicator Lamp (MIL) may be illuminated with Diagnostic Trouble Code (DTC) P0172/P0175 stored in the Engine Control Module (ECM). This may be caused by fueling feedback adaptions not robust to transient driving styles.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below to update the ECM software.
PARTS:
No parts required
TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD125_V5.06 Calibration File 73
Land Rover-approved Midtronics Vehicle Power Supply
Refer to Workshop Manual for any required special tools

WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
REPAIR PROCEDURE
UPDATE THE CONTROL MODULE SOFTWARE
CAUTION:
Ensure all ignition "ON" / ignition "OFF" requests are carried out; failure to perform these steps may cause damage to control modules in the vehicle.
CAUTION:
A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming.
1. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.
2. Turn ignition ON (engine not running).
NOTE:
IDS must be loaded with IDS-DVD125_V5.06 or later and Calibration File 73 or later.
3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
5. From the Session Type selection screen, choose "Diagnosis".
6. Select the "Selected Symptoms" tab, and then select:
a) Electrical > Instruments > Warning lamps > Engine malfunction lamp > Lamp illuminated and
b) Either DTC P0172 or DTC P0175 set in the PCM
7. Select "continue".
8. Select the Recommendations tab.
9. From the Recommendations tab, select Run to configure the control module
^ Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
25 MAY 2011
SECTION: 303
Engine MIL Illuminated with DTC P01721 / P0175 Stored
AFFECTED VEHICLE RANGE:
LR2 (LF) VIN: 8H000212 - BH252720
Model Year: 2008 - 2011
CONDITION SUMMARY:
Situation:
The engine Malfunction Indicator Lamp (MIL) may be illuminated with Diagnostic Trouble Code (DTC) P0172/P0175 stored in the Engine Control Module (ECM). This may be caused by fueling feedback adaptions not robust to transient driving styles.
Action:
In the event of a customer concern of the above, refer to the Repair Procedure outlined below to update the ECM software.
PARTS:
No parts required
TOOLS:
IDS with latest IDS-DVD and Calibration File; first available on IDS-DVD125_V5.06 Calibration File 73
Land Rover-approved Midtronics Vehicle Power Supply
Refer to Workshop Manual for any required special tools
WARRANTY:
NOTE:
Repair procedures are under constant review, and therefore times are subject to change; those quoted here must be taken as guidance only. Always refer to DDW to obtain the latest repair time.
DDW requires the use of causal part numbers. Labor only claims must show the causal part number with a quantity of zero.
REPAIR PROCEDURE
UPDATE THE CONTROL MODULE SOFTWARE
CAUTION:
Ensure all ignition "ON" / ignition "OFF" requests are carried out; failure to perform these steps may cause damage to control modules in the vehicle.
CAUTION:
A Land Rover-approved Midtronics Vehicle Power Supply must be connected to the vehicle battery during IDS diagnosis / module programming.
1. Connect the Land Rover-approved Midtronics Vehicle Power Supply to the vehicle battery.
2. Turn ignition ON (engine not running).
NOTE:
IDS must be loaded with IDS-DVD125_V5.06 or later and Calibration File 73 or later.
3. Connect the IDS to the vehicle and begin a new Symptom Driven Diagnostics (SDD) session.
4. Follow the on-screen prompts, allowing SDD to read the VIN and identify the vehicle.
5. From the Session Type selection screen, choose "Diagnosis".
6. Select the "Selected Symptoms" tab, and then select:
a) Electrical > Instruments > Warning lamps > Engine malfunction lamp > Lamp illuminated and
b) Either DTC P0172 or DTC P0175 set in the PCM
7. Select "continue".
8. Select the Recommendations tab.
9. From the Recommendations tab, select Run to configure the control module
^ Follow all on-screen instructions to complete this task.
10. Exit the current session.
11. Disconnect the IDS and the Midtronics Vehicle Power Supply from the vehicle.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
