2022 Kia K5 EXFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

NOTE:
  • Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
  • Maintain clean condition so that foreign substance does not get into the automatic transaxle.
  • Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
  1. Remove the under cover.

    (Refer to " REMOVAL AND INSTALLATION  ") 

  2. Drain the engine coolant.

    (Refer to Engine Mechanical System - " REPLACEMENT AND AIR BLEEDING  ") 

  3. Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.

    Tightening torque: 

    33.3 - 43.1 Nm (3.4 - 4.4 kgf m, 24.6 - 31.8 lb ft)

    G13834255Courtesy of KIA MOTORS AMERICA, INC.
    NOTE:
    • Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
    • The existing ATF drain plug gasket must be replaced with a new one (do not reuse).
  4. Remove the air cleaner assembly.

    (Refer to " REMOVAL AND INSTALLATION  ") 

  5. Remove the wiring bracket (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf m, 7.2 - 8.7 lb ft)

    G13834256Courtesy of KIA MOTORS AMERICA, INC.
  6. Remove the ATF warmer.

    (Refer to " Removal  ") 

  7. Remove the valve body cover (A) after removing the bolts.

    Tightening torque: 

    11.8 - 13.7 N m (1.2 - 1.4 kgf m, 8.7 - 10.1 lb ft)

    G13834257Courtesy of KIA MOTORS AMERICA, INC.
  8. Remove the main harness (A) after removing the bolts.

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf m, 7.2 - 8.7 lb ft)

    G13834258Courtesy of KIA MOTORS AMERICA, INC.
  9. Remove the detent spring (A), then remove the valve body assembly (B) by removing the bolts.

    Tightening torque: 

    1. 24.5 - 35.3 N m (2.5 - 3.6 kgf m, 18.1 - 26.0 lb ft)
    2. 9.8 - 11.8 N m (1.0 - 1.2 kgf m, 7.2 - 8.7 lb ft)
    G13834259Courtesy of KIA MOTORS AMERICA, INC.
  10. Disconnect the speed sensor connector (A).
    G13834260Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the speed sensor (A).

    Tightening torque: 

    9.8 - 11.8 N m (1.0 - 1.2 kgf m, 7.2 - 8.7 lb ft)

    G13834261Courtesy of KIA MOTORS AMERICA, INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.