2020 Kia Sorento LFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

  1. Remove the under cover.

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ").

  2. Drain the coolant.

    (Refer to Engine Mechanical System - "COOLANT ")

  3. Remove the ATF drain plug (A), allow the fluid to drain out and then reinstall the drain plug.

    Tightening torque: 

    33.3 - 43.1 N.m (3.4 - 4.4 kgf.m, 24.6 - 31.8 lb.ft)

    G12850081Courtesy of KIA MOTORS AMERICA, INC.
    NOTE: The existing ATF drain plug gasket must be replaced with new one. (Do not reuse it.)
  4. Remove the battery and battery tray.

    (Refer to Engine Electrical System - "BATTERY ")

  5. Remove the wiring bracket mounting bolt (A)

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12850082Courtesy of KIA MOTORS AMERICA, INC.
  6. Disconnect the air breather hose (A) from the valve body cover.
    G12850083Courtesy of KIA MOTORS AMERICA, INC.
  7. Disconnect the coolant pip (B) after removing the clamp (A).
    G12850084Courtesy of KIA MOTORS AMERICA, INC.
  8. Disconnect the ATF cooler hose (B) after removing the clamp (A).

    Tightening torque: 

    11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb.ft)

    G12850085Courtesy of KIA MOTORS AMERICA, INC.
  9. Remove the valve body cover (A) by loosening bolts.

    Tightening torque: 

    11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb.ft)

    G12850086Courtesy of KIA MOTORS AMERICA, INC.
  10. Remove the main harness (A) after removing the bolts.

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12850087Courtesy of KIA MOTORS AMERICA, INC.
  11. Remove the valve body assembly (A) after loosening the bolts.

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12850088Courtesy of KIA MOTORS AMERICA, INC.
  12. Disconnect the speed sensor connector (A).
    G12850089Courtesy of KIA MOTORS AMERICA, INC.
  13. Remove the speed sensor (A) after loosening the bolts.

    Tightening torque: 

    9.8 - 11.8 N.m (1.0 - 1.2 kgf.m, 7.2 - 8.7 lb.ft)

    G12850090Courtesy of KIA MOTORS AMERICA, INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.