Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2019 Kia Stinger Base, AWDFACTORY OEM SERVICE PROCEDURE
Automatic Transaxle System DTCS
AUTOMATIC TRANSAXLE SYSTEM DIAGNOSTIC TROUBLE CODE IDENTIFICATION
| DTC | Description |
|---|---|
| P0601-00 | Internal Control Module Memory Check Sum Error |
| P0705-12 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| P0705-14 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| P0705-1C | Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| P0706-61 | Transmission Range Sensor Circuit Range/Performance |
| P0706-96 | Transmission Range Sensor Circuit Range/Performance |
| P0711-00 | Transmission Fluid Temperature Sensor 'A' Circuit Range/Performance |
| P0712-00 | Transmission Fluid Temperature Sensor 'A' Circuit Low Input |
| P0713-00 | Transmission Fluid Temperature Sensor 'A' Circuit High Input |
| P0717-00 | Input/Turbine Speed Sensor 'A' Circuit No Signal |
| P0721-00 | Output Speed Sensor Circuit Range/Performance |
| P0722-00 | Output Speed Sensor Circuit No Signal |
| P0729-00 | Gear 6 Incorrect Ratio |
| P0730-00 | Gear 8 Incorrect Ratio |
| P0731-00 | Gear 1 Incorrect Ratio |
| P0732-00 | Gear 2 Incorrect Ratio |
| P0733-00 | Gear 3 Incorrect Ratio |
| P0734-00 | Gear 4 Incorrect Ratio |
| P0735-00 | Gear 5 Incorrect Ratio |
| P0741-00 | Torque Converter Clutch Circuit Performance Or Stuck Off |
| P0743-00 | Torque Converter Clutch Circuit Electrical |
| P0748-00 | Pressure Control Solenoid Valve (VFS) 'A' Electrical |
| P0753-00 | Shift Control Solenoid Valve 'A' Electrical (UD/C) |
| P0758-00 | Shift Control Solenoid Valve 'B' Electrical (6/C) |
| P075A-00 | ON/OFF Solenoid Circuit [SBC] |
| P0763-00 | Shift Control Solenoid Valve 'C' Electrical (35R/C) |
| P0768-00 | Shift Control Solenoid Valve 'D' Electrical (4&OD/C) |
| P076A-00 | Park System Fault (SBW) |
| P076D-00 | ON/OFF Solenoid C (Parking) (SBW) |
| P076F-00 | Gear 7 Incorrect Ratio |
| P0773-00 | Shift Control Solenoid Valve 'E' Electrical (27/B) |
| P0785-00 | ON/OFF Solenoid A (Drive) (SBW) |
| P078A-00 | ON/OFF Solenoid B (Reverse) (SBW) |
| P0880-00 | TCM Power Input Signal |
| P0881-00 | TCM Power Input Signal Range/Performance |
| P0995-00 | Auto Shift Manual Mode Circuit |
| P1C28-00 | OPI Current High |
| P1C2B-00 | OPI Hall Effect Sensor Error |
| P2709-00 | Shift Control Solenoid Valve 'F' Electrical (8LR/B) |
| U0001-00 | High Speed CAN Communication Bus |
| U0100-00 | Lost Communication With ECM/PCM 'A' |
| U0103-00 | Lost Communication With Gear Shift Control Module 'A' |
| U0287-00 | OPI CAN Time Out |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.