Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2019 Kia Stinger Base, AWDFACTORY OEM SERVICE PROCEDURE
Engine Control System
ENGINE CONTROL SYSTEM TIGHTENING TORQUE SPECIFICATIONS
| Item | kgf.m | N.m | lb.ft |
|---|---|---|---|
| ECM bracket mounting bolt/nut | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Electronic Throttle Control (ETC) Module mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Manifold Absolute Pressure Sensor (MAPS) mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Intake Air Temperature Sensor (IATS) mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Boost Pressure Sensor (BPS) mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Crankshaft position sensor (CKPS) mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Camshaft position sensor (CMPS) [Bank 1/Intake] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Camshaft position sensor (CMPS) [Bank 1/Exhaust] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Knock Sensor (KS) mounting bolt | 1.9 - 2.4 | 18.6 - 23.5 | 13.7 - 17.4 |
| Heated oxygen sensor (HO2S) [Bank 1/sensor 1] | 4.0 - 5.0 | 39.2 - 49.1 | 28.9 - 36.2 |
| Heated oxygen sensor (HO2S) [Bank 1/sensor 2] | 4.0 - 5.0 | 39.2 - 49.1 | 28.9 - 36.2 |
| Rail Pressure Sensor (RPS) | 1.8 - 2.2 | 18.0 - 22.0 | 13.3 - 16.2 |
| Accelerator pedal module mounting bolt/nut | 0.9 - 1.4 | 8.8 - 13.7 | 6.5 - 10.1 |
| CVVT Oil Control Valve (OCV) [Bank 1/Exhaust] mounting bolt | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
| Variable Charge Motion Actuator (VCMA) mounting bolt | 1.0 - 1.4 | 9.8 - 11.8 | 7.2 - 8.7 |
| Oil Temperature Sensor (OTS) | 3.5 - 4.5 | 34.3 - 44.1 | 25.3 - 32.5 |
| RCV Control Solenoid Valve | 1.0 - 1.2 | 9.8 - 11.8 | 7.2 - 8.7 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.