Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Audio/Video/Navigation (AVN) System: Troubleshooting: Sound
- Features/Misdiagnose cases
Inspection Description (1) System features - Ignition ON (H/U β B+, ACC Power on), H/U Power ON β Sound for Radio, Media, Navigation, Voice Guidance.
- External amp is attached at the trunk. External amp communicates with H/U via CAN (Control Area Network)
(*External amp location may vary)
(2) Misdiagnose cases - Mute or irregular sound might occur if customer have changed sound settings (position, tone, bass, middle, treble)
(This is normal, yet misdiagnosed)
- Poor sound quality if low-quality soundtrack is played
(Example: Application like I-MEPS will provide poor sound quality. Customers using BT stream to play I-MEPS claims H/U replacement for low sound quality)
- Sound output - Common
Inspection Description (1) Vehicle modification - Check vehicle modification (Front Panel, Black box, Mic, Taxi meter, etc.)
(2) Duplicate issue - Check sound/noise output
- Check H/U settings
(3) Check H/U/Amp/Cable - Check defect of 1) H/U, 2) amp, 3) connector defect in order (Ext. amp spec)
- Check defect of 1) H/U, 2) connector (For Internal amp)
(4) Defect caused by Ext. parts N/A (5) Check part defect - Check defect by replacing H/U
- Sound Output_Noise (H/U_Ext. Amp)
Inspection Procedure Description (1) Duplicate issue
1. Check H/U Setting (Internal/External amp)- Check H/U Setting (Internal/External amp)
- Setting β Sound - Check position, tone settings
- Set position, tone to 'center'.
βUser may have changed settings to mute speakers
- Reset setting by pressing center button, then check sound
- Check H/U Setting (Internal/External amp)
- Sound Output_Noise (External AMP_Cable)
Inspection Procedure Description (2) Inspect H/U/AMP/Cable
1. AMP
(External AMP)- Check AMP (External amp)
- Review defect
- Check amp battery and ACC voltage (9V - 16V)
β Vehicle issue if unable to read voltage
- Check audio output
β Amp issue if no audio output - Check speaker impedance
β If not normal, check wire/cable, speaker (disconnect the cable and test)
- Check amp battery and ACC voltage (9V - 16V)
- Review defect
(2) Inspect H/U/AMP/Cable
2. Cable
(External amp)- Check cable (External amp)
- AMP β H/U Line inspection
- MMCAN +/-: Check open/short using multi-meter
- SPDIF +/-: Check open/short using multi-meter
- NAVI +/-: Check open/short using multi-meter
βIssue occurs (=Open) -> Cable wiring issue
- AMP β H/U Line inspection
(2) Check cable connection
3. Cable connection (Internal/External amp)- Check cable connection to H/U, AMP and mid connector
* Check amp connector (For external amp)
* Check if mid connector is present and find location at the red mark
* Check H/U connector
- Check connection status of Part β Connector
- Check noise by pulling cable a little
- Check for incorrect cable mounting
βIf issue continues, re-connect the cable and re-test
- Check connection status of Part β Connector
(2) Check H/U/AMP/Cable
4. Check for cable defect (Internal/External amp)- Check for cable defect (Internal/external amp)
Courtesy of KIA MOTORS AMERICA, INC.
Factory Service ToolsUse the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
- Check AMP (External amp)
