2017 Kia Soul Base, Automatic TransFACTORY OEM SERVICE PROCEDURE

Repair Procedures: Removal

  1. Turn ignition switch OFF and disconnect the negative (-) battery cable.
  2. Remove the ECM.

    (Refer to Engine Control/Fuel System - "ENGINE CONTROL MODULE (ECM) ")

  3. Remove the brake fluid from the master cylinder reservoir with a syringe.
    CAUTION:
    • Be sure to completely remove foreign substances from around brake fluid reservoir and cap before opening the reservoir cap. If not, it may cause contamination of brake fluid and deterioration in braking performance.
    • Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.
  4. Disconnect the brake tube (A) from the master cylinder by loosening the tube flare nut.

    Tightening torque  :

    18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)

    Fig 1: Locating Brake Tube With Tube Flare Nuts
    G12225625Courtesy of KIA MOTORS AMERICA, INC.
  5. Pull up the lock of the HECU connector and then disconnect the connector (B).
    Fig 2: Locating HECU Connector
    G12225626Courtesy of KIA MOTORS AMERICA, INC.
  6. Loosen the flare nuts and then remove the brake tube (A).

    Tightening torque  :

    18.6 ~ 22.6 N.m (1.9 ~ 2.3 kgf.m, 13.7 ~ 16.6 lb-ft)

    Fig 3: Locating Brake Tubes
    G12225627Courtesy of KIA MOTORS AMERICA, INC.
  7. Disconnect the brake tubes (B) from the HECU by unlocking the nuts counterclockwise with a spanner.

    Tightening torque  :

    12.7 ~ 16.7 N.m (1.3 ~ 1.7 kgf.m, 9.4 ~ 12.3 lb-ft)

  8. Remove the engine room under cover. [G2.0 NU GDI only]

    (Refer to Engine Mechanical System - "ENGINE ROOM UNDER COVER ")

  9. Install the jack under the edge of lower oil pan to support the engine. [G2.0 NU GDI only]
    NOTE: Put the rubber block between the jack and oil pan to avoid damaging the oil pan.
  10. Remove the engine mounting support bracket (A). [G2.0 NU GDI only]

    Tightening torque  :

    78.5 ~ 98.1 N.m (8.0 ~ 10.0 kgf.m, 57.9 ~ 72.3 lb-ft)

    Fig 4: Locating Engine Mounting Support Bracket
    G12225628Courtesy of KIA MOTORS AMERICA, INC.
  11. Slowly lower the jack. [G2.0 NU GDI only]
  12. Loosen the HECU bracket nuts (A) and then remove HECU and bracket.

    Tightening torque  :

    19.6 ~ 29.4 N.m (2.0 ~ 3.0 kgf.m, 14.5 ~ 21.7 lb-ft)

    Fig 5: Locating HECU Bracket Nuts
    G12225629Courtesy of KIA MOTORS AMERICA, INC.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.