Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Kia Niro EXFACTORY OEM SERVICE PROCEDURE
DTC Index
DTC INDEX
| DTC | Description |
|---|---|
| DTC P1160 | 00: Duration Of The KEY OFF Is Too Short |
| DTC P1230 | 00: Low Pressure Fuel Pump Malfunction |
| DTC P1233 | 00: Low Pressure Fuel System - High Deviation Between Target And Current Pressure |
| DTC P1520 | 00: Engine Coolant Temperature Sensor Circuit - Low (Exhaust Heat Recovery System) |
| DTC P1521 | 00: Engine Coolant Temperature Sensor Circuit - High (Exhaust Heat Recovery System) |
| DTC P2025 | 00: Evaporative Emissions Fuel Vapor Temperature Sensor Circuit Performance |
| DTC P2026 | 00: Evaporative Emissions Fuel Vapor Temperature Sensor Circuit - Low Voltage |
| DTC P2027 | 00: Evaporative Emissions Fuel Vapor Temperature Sensor Circuit - High Voltage |
| DTC P2096 | 00: Post Catalyst Fuel Trim System Too Lean (Bank 1) |
| DTC P2097 | 00: Post Catalyst Fuel Trim System Too Rich (Bank 1) |
| DTC P2101 | 00: Throttle Actuator Control Motor Circuit Range/Performance |
| DTC P2118 | 00: Throttle Actuator Control Motor Current Range/Performance |
| DTC P2119 | 00: Throttle Actuator Control Throttle Body Range/Performance |
| DTC P2122 | 00: Accelerator Position Sensor 1 Signal Circuit - Low Input |
| DTC P2123 | 00: Accelerator Position Sensor 1 Signal Circuit - High Input |
| DTC P2127 | 00: Accelerator Position Sensor 2 Signal Circuit - Low Input |
| DTC P2128 | 00: Accelerator Position Sensor 2 Signal Circuit - High Input |
| DTC P2138 | 00: Accelerator Position Sensor 1 & 2 Signal Voltage Correlation |
| DTC P2147 | 00: Fuel Injector Group 'A' Supply Voltage Circuit - Low |
| DTC P2148 | 00: Fuel Injector Group 'A' Supply Voltage Circuit - High |
| DTC P2150 | 00: Fuel Injector Group 'B' Supply Voltage Circuit - Low |
| DTC P2151 | 00: Fuel Injector Group 'B' Supply Voltage Circuit - High |
| DTC P2159 | 00: Vehicle Speed Sensor 'B' Range/Performance (Wheel Speed Sensor) |
| DTC P2195 | 00: O2 Sensor Signal Stuck Lean (Bank 1 / Sensor 1) |
| DTC P2196 | 00: O2 Sensor Signal Stuck Rich (Bank 1 / Sensor 1) |
| DTC P219C | 00: Cylinder 1 Air-Fuel Ratio Imbalance |
| DTC P219D | 00: Cylinder 2 Air-Fuel Ratio Imbalance |
| DTC P219E | 00: Cylinder 3 Air-Fuel Ratio Imbalance |
| DTC P219F | 00: Cylinder 4 Air-Fuel Ratio Imbalance |
| DTC P2227 | 00: Barometric Pressure Circuit Range/Performance |
| DTC P2228 | 00: Barometric Pressure Circuit - Low Input |
| DTC P2229 | 00: Barometric Pressure Circuit - High Input |
| DTC P2237 | 00: O2 Sensor Pumping Current Circuit/Open (Bank 1 / Sensor 1) |
| DTC P2240 | 00: O2 Sensor Positive Current Control Circuit/Open (Bank 2 / Sensor 1) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
