Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2015SEDONA LREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEXELECTRONIC STABILITY CONTROL (ESC) DTCS
2015 Kia Sedona L
Electronic Stability Control (ESC) DTCS
2015 Kia Sedona LSECTION Electronic Stability Control (ESC) DTCS
ELECTRONIC STABILITY CONTROL (ESC) DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| C1101 | Battery Voltage High |
| C1102 | Battery Voltage Low |
| C1200 | Wheel Speed Sensor Front-LH Open/Short |
| C1201 | Wheel Speed Sensor Front-LH Range/Performance/Intermittent |
| C1202 | Wheel Speed Sensor Front-LH Invalid/no Signal |
| C1203 | Wheel Speed Sensor Front-RH Open/Short |
| C1204 | Wheel Speed Sensor Front-RH Range/Performance/Intermittent |
| C1205 | Wheel Speed Sensor Front-RH Invalid/no Signal |
| C1206 | Wheel Speed Sensor Rear-LH Open/Short |
| C1207 | Wheel Speed Sensor Rear-LH Range/Performance/Intermittent |
| C1208 | Wheel Speed Sensor Rear-LH Invalid/no Signal |
| C1209 | Wheel Speed Sensor Rear-RH Open/Short |
| C1210 | Wheel Speed Sensor Rear-RH Range/Performance/Intermittent |
| C1211 | Wheel Speed Sensor Rear-RH Invalid/no Signal |
| C1235 | Primary Pressure Sensor-Electrical |
| C1237 | Primary Pressure Sensor-Signal |
| C1260 | Steering Angle Sensor Circuit-Signal |
| C1261 | Steering Angle Sensor Not Calibrated |
| C1283 | Yaw Rate & G Sensor-Signal |
| C1285 | Longitudinal G Sensor Not Calibrated |
| C1503 | TCS/ESC (ESP) Switch Error |
| C1542 | Brake Circuit Error |
| C1604 | ECU Hardware Error |
| C1605 | CAN Hardware Error |
| C1611 | CAN Time-out EMS |
| C1612 | CAN Time-out TCM |
| C1613 | CAN signal error ECM (Check ECM) |
| C1616 | CAN Bus OFF |
| C1623 | CAN Time-out Steering Angle Sensor |
| C1638 | CAN Time-Out SCC |
| C1643 | CAN Time-out Yaw Rate & G Sensor |
| C1649 | CAN time-out ECM for SCC (Check ECM) |
| C1650 | CAN signal error SCC |
| C1687 | CAN Time-out VSM2 (MDPS) |
| C1688 | VSM2 (MDPS) Signal Error |
| C1702 | Variant Coding Error |
| C2112 | Valve Relay Error |
| C2228 | CAN signal error TCM for SCC (Check TCM) |
| C2380 | ABS/TCS/ESC (ESP) Valve Error |
| C2402 | Motor Electrical |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.