SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSKIA2010FORTE EX, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCEENGINE CONTROL SYSTEMSENGINE CONTROL/FUEL SYSTEM - GENERAL INFORMATIONSPECIFICATIONSSENSORS SPECIFICATIONS
2010 Kia Forte EX, Standard

Sensors Specifications

2010 Kia Forte EX, StandardSECTION Sensors Specifications

Manifold Absolute Pressure Sensor (MAPS)

  • Type: Piezo-resistive pressure sensor type
  • Specification
MANIFOLD ABSOLUTE PRESSURE SENSOR SPECIFICATIONS

Pressure (kPa) Output Voltage (V)
20.0 0.79
46.7 1.84
101.3 4.0

Intake Air Temperature Sensor (IATS)

  • Type: Thermistor type
  • Specification
INTAKE AIR TEMPERATURE SENSOR SPECIFICATIONS

Temperature [°C (°F)] Resistance (kΩ)
-40 (-40) 40.93 ~ 48.35
-20 (-4) 13.89 ~ 16.03
0 (32) 5.38 ~ 6.09
10 (50) 3.48 ~ 3.90
20 (68) 2.31 ~ 2.57
40 (104) 1.08 ~ 1.21
50 (122) 1.56 ~ 1.74
60 (140) 0.54 ~ 0.62
80 (176) 0.29 ~ 0.34

Engine Coolant Temperature Sensor (ECTS)

  • Type: Thermistor type
  • Specification
ENGINE COOLANT TEMPERATURE SENSOR SPECIFICATIONS

Temperature [°C (°F)] Resistance (kΩ)
-40 (-40) 48.14
-20 (-4) 14.13 ~ 16.83
0 (32) 5.79
20 (68) 2.31 ~ 2.59
40 (104) 1.15
60 (140) 0.59
80 (176) 0.32

Throttle Position Sensor (TPS) [integrated into ETC Module]

  • Type: Variable resistor type
  • Specification
THROTTLE POSITION SENSOR SPECIFICATIONS

Throttle Angle (°) Output Voltage (V)
TPS1 TPS2
0 0 5.0
10 0.48 4.52
20 0.95 4.05
30 1.43 3.57
40 1.90 3.10
50 2.38 2.62
60 2.86 2.14
70 3.33 1.67
80 3.81 1.19
90 4.29 0.71
100 4.76 0.24
105 5.0 0
C.T (6~15°) 0.29 ~ 0.71 4.29 ~ 4.71
W.O.T (93~102°) 4.43 ~ 4.86 0.14 ~ 0.57
THROTTLE POSITION SENSOR SPECIFICATIONS

Item Resistance (kΩ)
TPS1 0.875 ~ 1.625 [20°C (68°F)]
TPS2 0.875 ~ 1.625 [20°C (68°F)]

Crankshaft Position Sensor (CKPS)

  • Type: Hall effect type

Camshaft Position Sensor (CMPS)

  • Type: Hall effect type

Knock Sensor (KS)

  • Type: Piezo-electricity type
  • Specification
KNOCK SENSOR SPECIFICATIONS

Item Specification
Capacitance (pF) 850 ~ 1,150

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]

  • Type: Zirconia (ZrO2) [Linear] Type
  • Specification
HEATED OXYGEN SENSOR (BANK 1/SENSOR 1) SPECIFICATIONS

Item Specification
Heater Resistance (Ω) 2.5 ~ 4.0 [20°C (69.8°F)]

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]

  • Type: Zirconia (ZrO2) [Binary] Type
  • Specification
HEATED OXYGEN SENSOR (BANK 1/SENSOR 2) OUTPUT VOLTAGE SPECIFICATIONS

A/F Ratio (λ) Output Voltage (V)
RICH Approx. 0.9
LEAN Approx. 0.04
HEATER RESISTANCE SPECIFICATION

Item Specification
Heater Resistance (Ω) 3.3 ~ 4.1 [21°C (69.8°F)]

Accelerator Position Sensor (APS)

  • Type: Variable resistor type
  • Specification
ACCELERATOR POSITION SENSOR OUTPUT VOLTAGE SPECIFICATIONS

Accelerator Position Output Voltage (V)
APS1 APS2
C.T 0.7 ~ 0.8 0.275 ~ 0.475
W.O.T 3.85 ~ 4.35 1.75 ~ 2.35
APS1 AND APS2 RESISTANCE SPECIFICATIONS

Items Sensor Resistance (kΩ)
APS1 0.8 ~ 1.6 [20°C (68°F)]
APS2 0.9 ~ 2.5 [20°C (68°F)]

Fuel Tank Pressure Sensor (FTPS)

  • Type: Piezo - Resistivity type
  • Specification
FUEL TANK PRESSURE SENSOR SPECIFICATIONS

Pressure (kPa) Output Voltage (V)
-6.67 0.5
0 2.5
+6.67 4.5
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.