Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Kia Borrego LX, 3.8 1, RWDFACTORY OEM SERVICE PROCEDURE
Abs/ESC System DTCS
ABS/ESC SYSTEM DIAGNOSTIC TROUBLE CODES (DTC) LIST
| DTC | Description |
|---|---|
| C1101 | Battery Voltage High |
| C1102 | Battery Voltage Low |
| C1112 | Sensor Source Voltage |
| C1200 | Wheel Speed Sensor Front-LH Open/Short |
| C1201 | Wheel Speed Sensor Front-LH Range/Performance/Intermittent |
| C1202 | Wheel Speed Sensor Front-LH Invalid/No signal |
| C1203 | Wheel Speed Sensor Front-RH Open/Short |
| C1204 | Wheel Speed Sensor Front-RH Range/Performance/Intermittent |
| C1205 | Wheel Speed Sensor Front-RH Invalid/No signal |
| C1206 | Wheel Speed Sensor Rear-LH Open/Short |
| C1207 | Wheel Speed Sensor Rear-LH Range/Performance/Intermittent |
| C1208 | Wheel Speed Sensor Rear-LH Invalid/No signal |
| C1209 | Wheel Speed Sensor Rear-RH Open/Short |
| C1210 | Wheel Speed Sensor Rear-RH Range/Performance/Intermittent |
| C1211 | Wheel Speed Sensor Rear-RH Invalid/No signal |
| C1235 | Primary Pressure Sensor - Electrical |
| C1237 | Primary Pressure Sensor - Signal |
| C1260 | Steering Angle Sensor Circuit - Signal |
| C1261 | Steering Angle Sensor Not Calibrated |
| C1274 | Longitudinal G Sensor Open/Short |
| C1275 | Longitudinal G Sensor Range/Performance Error |
| C1282 | Yaw Rate & Lateral G Sensor - Electrical |
| C1283 | Yaw Rate & Lateral G Sensor - Signal |
| C1285 | Longitudinal G Sensor Not Calibrated |
| C1503 | TCS/ESC Switch Error |
| C1513 | Brake Switch Error |
| C1526 | DBC Switch Error |
| C1604 | ECU Hardware Error |
| C1605 | CAN Hardware Error |
| C1611 | CAN Time-Out ECM |
| C1612 | CAN Time-Out TCM |
| C1613 | CAN Wrong Message |
| C1616 | CAN Bus Off |
| C1623 | CAN Time-out Steering Angle Sensor |
| C1627 | CAN Time-Out 4WD |
| C1647 | CAN Hardware Error - Sensor Channel |
| C1702 | Variant Coding Error |
| C2112 | Valve Relay Error |
| C2130 | Brake Lamp Relay Error |
| C2227 | Excessive Temperature of Brake Disc |
| C2380 | ABS/TCS/ESC Valve Error |
| C2402 | Motor Failure |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.