Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2006 Kia Rio L4-1.6LFACTORY OEM SERVICE PROCEDURE
Connecting Rod, Engine
Connecting Rod
Piston pin
Piston pin outer diameter 18.001 - 18.007 mm (0.7087 - 0.7089 inch)
Piston pin hole inner diameter 18.016 - 18.021 mm (0.7093 - 0.7095 inch)
Piston pin hole clearance 0.011 - 0.018 mm (0.0004 - 0.0007 inch)
Connecting rod small end hole inner diameter 17.974 - 17.985 mm (0.7076 - 0.7081 inch)
Connecting rod small end hole - 0.033 - -0.016 mm (-0.0013 - -0.0006 inch) clearance
Piston pin press-in load 500 - 1,500 kg (1,102 - 3,306 lbs.)
Connecting rod
Connecting rod big end inner diameter 48.000 - 48.018 mm (1.8898 - 1.8905 inch)
Side clearance
Specifications 0.10 - 0.25 mm (0.0039 - 0.0098 inch)
Limit 0.4 mm (0.0157 inch)
Connecting rod cap nut
Quantity 8
Tightening Torque 31.4 - 34.3 Nm (3.2 - 3.5 kgf.m, 23.1 - 25.3 ft. lbs.)
Piston pin
Piston pin outer diameter 18.001 - 18.007 mm (0.7087 - 0.7089 inch)
Piston pin hole inner diameter 18.016 - 18.021 mm (0.7093 - 0.7095 inch)
Piston pin hole clearance 0.011 - 0.018 mm (0.0004 - 0.0007 inch)
Connecting rod small end hole inner diameter 17.974 - 17.985 mm (0.7076 - 0.7081 inch)
Connecting rod small end hole - 0.033 - -0.016 mm (-0.0013 - -0.0006 inch) clearance
Piston pin press-in load 500 - 1,500 kg (1,102 - 3,306 lbs.)
Connecting rod
Connecting rod big end inner diameter 48.000 - 48.018 mm (1.8898 - 1.8905 inch)
Side clearance
Specifications 0.10 - 0.25 mm (0.0039 - 0.0098 inch)
Limit 0.4 mm (0.0157 inch)
Connecting rod cap nut
Quantity 8
Tightening Torque 31.4 - 34.3 Nm (3.2 - 3.5 kgf.m, 23.1 - 25.3 ft. lbs.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
