Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2024WAGONEER L SERIES II, RWDREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSFLUIDS
2024 Jeep Wagoneer L Series II, RWD
Quick Lookups: Fluids
2024 Jeep Wagoneer L Series II, RWDSECTION Fluids
| FLUID CAPACITIES | |||||||
|---|---|---|---|---|---|---|---|
| Fluid Type | Application | Standard | Metric | Fluid Spec | Note | S/H | |
| Air Cond Compressor Oil | 7.08 OZS. | 0.2 L | ND-12 | S | |||
| Air Cond Refrigerant | 2.13 LBS. | 0.96 KG | R-1234yf | S | |||
| Automatic Transmission Fluid | 8.98 QTS. | 8.49 L | MOPAR ZF 8&9 Speed Automatic Transmission Fluid, or equivalent | Dry fill capacity, depending on the type and size of the internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler may vary. Failure to use the correct fluid may affect the function or performance of the transmission. | S | ||
| Brake Fluid | N/A | N/A | MORAR Brake Fluid DOT 3, SAE J1703 | If MOPAR Brake Fluid DOT 3 is not available, then MOPAR Brake and Clutch Fluid DOT 4 (P/N 04549625AC), is acceptable. | S | ||
| Differential Gear Oil | Front Axle,215FD | 1.20 QTS. | 1.13 L | MOPAR GL-5 Synthetic Axle Lubricant SAE 75W-85 | Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure. | S | |
| Differential Gear Oil | Rear Axle,260RDU,w/Electronic Limited Slip Differential | 1.50 QTS. | 1.41 L | MOPAR GL-5 Electronic Limited Slip Synthetic Axle Lubricant SAE 75W-85 with friction modifier | Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure. | S | |
| Differential Gear Oil | Rear Axle,260RDU,w/Mechanical Limited Slip Differential | 1.50 QTS. | 1.41 L | MOPAR GL-5 Mechanical Limited Slip Synthetic Axle Lubricant SAE 75W-85 with friction modifier | Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure. | S | |
| Engine Coolant | Engine Coolant | 16.60 QTS. | 15.7 L | MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-12106 | Includes: heater and coolant recovery tank filled to "max" level. | S | |
| Engine Coolant | Intercooler | 2.90 QTS. | 2.74 L | MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of Chrysler Material Standard MS-12106 | Includes: heater and coolant recovery tank filled to "max" level. | S | |
| Engine Oil | Series II,Series III,3.0L Eng | w/Filter,w/HO Engine | 7.50 QTS. | 7.09 L | API - SAE 0W-40 Full Synthetic Engine Oil | Usage of earlier API certification levels (such as API-SN or prior) can result in engine damage and is not covered by the New Vehicle Limited Warranty. | S |
| Transfer Case Fluid | 1.50 QTS. | 1.41 L | MOPAR Mobile LT | Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure. | S | ||
| Windshield Washer Fluid | N/A | N/A | Windshield Washer Solvent only | Follow the Manufacturer's Instructions for the mixture ratio. | S | ||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.