Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2023 Jeep Renegade LatitudeFACTORY OEM SERVICE PROCEDURE
Sensor, Left Blind Spot (LBSS)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C1000-44 | ELECTRONIC CONTROL UNIT-DATA MEMORY FAILURE |
| C1000-45 | ELECTRONIC CONTROL UNIT-PROGRAM MEMORY FAILURE |
| C1000-46 | ELECTRONIC CONTROL UNIT-CALIBRATION-PARAMETER MEMORY FAILURE |
| C1000-47 | ELECTRONIC CONTROL UNIT-WATCHDOG-SAFETY FAILURE |
| C1002-02 | LBSS RADAR SENSOR ADDRESS FAULT-GENERAL SIGNAL FAILURE |
| C1003-04 | BLIND SPOT SENSOR PROBLEM-SYSTEM INTERNAL FAILURES |
| C1003-49 | BLIND SPOT SENSOR PROBLEM-INTERNAL ELECTRONIC FAILURE |
| C1003-97 | BLIND SPOT SENSOR PROBLEM-COMPONENT OR SYSTEM OPERATION OBSTRUCTED OR BLOCKED |
| C1004-16 | BATTERY VOLTAGE INPUT CIRCUIT-CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1004-17 | BATTERY VOLTAGE INPUT CIRCUIT-CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C1006-64 | STATUS_BH_BCM2.TURNINDICATIONSTS (FROM BODY CONTROL MODULE) - SIGNAL PLAUSIBILITY FAILURE |
| C1008-64 | VEHICLE CONFIGURATION MISMATCH - SIGNAL PLAUSIBILITY FAILURE |
| C100B-11 | LEFT BLIND SPOT SENSOR-CIRCUIT SHORT TO GROUND |
| C100B-15 | LEFT BLIND SPOT SENSOR-CIRCUIT SHORT TO BATTERY OR OPEN |
| C100B-4B | LEFT BLIND SPOT SENSOR-OVER TEMPERATURE |
| C2000-64 | STATUS-TTM.TRAILERGENERICFAILSTS-SIGNAL PLAUSIBILITY FAILURE |
| C2001-64 | STATUS-BH-BCM1.PARKBRAKESTS-SIGNAL PLAUSIBILITY FAILURE |
| C2002-64 | STATUS-CCAN5.SHIFTLEVERPOSITION-SIGNAL PLAUSIBILITY FAILURE |
| U0010-87 | B CAN-MISSING MESSAGE |
| U0010-88 | B CAN-BUS OFF |
| U146D-64 | LBSS OPERATIONALMODESTS-SIGNAL PLAUSIBILITY FAILURE |
| U148D-64 | IPC-VEHICLE-SETUP.BSDENABLE-SIGNAL PLAUSIBILITY FAILURE |
| U149D-64 | STATUS-CCAN3.VEHICLESPEEDVSOSIGFAILSTS-SIGNAL PLAUSIBILITY FAILURE |
| U1700-86 | BODY COMPUTER MODULE (BCM)-SIGNAL INVALID |
| U1700-87 | BODY COMPUTER MODULE (BCM)-MISSING MESSAGE |
| U1703-86 | INSTRUMENT PANEL CLUSTER (IPC)-SIGNAL INVALID |
| U1703-87 | INSTRUMENT PANEL CLUSTER (IPC)-MISSING MESSAGE |
| U1752-86 | RIGHT BLIND SPOT SENSOR (RBSS)-SIGNAL INVALID |
| U1752-87 | RIGHT BLIND SPOT SENSOR (RBSS)-MISSING MESSAGE |
| U1763-86 | TTM (TRAILER TOW MODULE)-SIGNAL INVALID |
| U1763-87 | TTM (TRAILER TOW MODULE)-MISSING MESSAGE |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.