Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2023COMPASS REDREPAIR AND DIAGNOSISENGINE PERFORMANCESYSTEM2.0L - DTCS P0507 TO P0585
2023 Jeep Compass Red
2.0L - DTCS P0507 To P0585
2023 Jeep Compass RedSECTION 2.0L - DTCS P0507 To P0585
- DTC Troubleshooting
- P0507-Idle Speed Performance Higher Than Expected
- P050B-Cold Start Ignition Timing Performance
- P0513-Invalid Skim Key
- P051C-Crankcase Pressure Sensor "A" Circuit Low
- P051D-Crankcase Pressure Sensor "A" Circuit High
- P0520-Engine Oil Pressure Sensor Circuit
- P0521-Engine Oil Pressure Sensor Performance
- P0522-Engine Oil Pressure Sensor Circuit Low
- P0523-Engine Oil Pressure Sensor Circuit High
- P052B-Cold Start Intake Camshaft Position Timing Over-Retarded - Bank 1 Sensor 1
- P0532-A/C Pressure Sensor Circuit Low
- P0533-A/C Pressure Sensor Circuit High
- P053F-Cold Start Fuel Pressure Performance Bank 1
- P054A-Cold Start Exhaust Camshaft Position Timing Over-Advanced - Bank 1 Sensor 2
- P0562-Battery/System Voltage Low
- P0563-Battery/System Voltage High
- P056E-Cold Start Turbocharger/Supercharger Boost Control "A" Performance
- P0571-Brake Switch 1 Performance
- P057B-Brake Pedal Position Sensor "A" Circuit Performance
- Notes
- Theory Of Operation-Braking Systems
- Component Functional Description - Brake Pedal Position Sensor
- Component Functional Description - Hydraulic Control Unit (HCU) Assembly
- Component Functional Description - Wheel Speed Sensors
- Component Functional Description - Steering Angle Sensor
- Component Functional Description - Anti-Lock Brake System Control Module (Abs)
- Technical Data-Braking System Messages
- When Monitored
- Set Condition
- Default Action
- Possible Causes
- Diagnostic Overview
- Check For An Active Or Intermittent Condition
- Diagnostic Test - Non-EBOOSTER Brake System - Pcm
- Diagnostic Test-Wheel Speed Sensor Faults
- P057C-Brake Pedal Position Sensor Circuit Low
- Notes
- Theory Of Operation-Braking Systems
- Component Functional Description - Brake Pedal Position Sensor
- Component Functional Description - Hydraulic Control Unit (HCU) Assembly
- Component Functional Description - Wheel Speed Sensors
- Component Functional Description - Steering Angle Sensor
- Component Functional Description - Anti-Lock Brake System Control Module (Abs)
- Technical Data-Braking System Messages
- When Monitored
- Set Condition
- Default Action
- Possible Causes
- Diagnostic Overview
- Check For An Active Or Intermittent Condition
- Diagnostic Test - Non-EBOOSTER Brake System - Pcm
- Diagnostic Test-Wheel Speed Sensor Faults
- P057D-Brake Pedal Position Sensor Circuit High
- Notes
- Theory Of Operation-Braking Systems
- Component Functional Description - Brake Pedal Position Sensor
- Component Functional Description - Hydraulic Control Unit (HCU) Assembly
- Component Functional Description - Wheel Speed Sensors
- Component Functional Description - Steering Angle Sensor
- Component Functional Description - Anti-Lock Brake System Control Module (Abs)
- Technical Data-Braking System Messages
- When Monitored
- Set Condition
- Default Action
- Possible Causes
- Diagnostic Overview
- Check For An Active Or Intermittent Condition
- Diagnostic Test - Non-EBOOSTER Brake System - Pcm
- Diagnostic Test-Wheel Speed Sensor Faults
- P0585-Speed Control Switch 1 / 2 Correlation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.