Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Jeep Renegade LimitedFACTORY OEM SERVICE PROCEDURE
Module, Electronic Shift (ESM), 948TE
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| P0562-00 | SYSTEM VOLTAGE LOW |
| P0563-00 | SYSTEM VOLTAGE HIGH |
| P0606-00 | CONTROL MODULE PROCESSOR |
| P0607-00 | CONTROL MODULE PERFORMANCE |
| P060A-00 | INTERNAL CONTROL MODULE MONITORING PROCESSOR PERFORMANCE |
| P0814-00 | TRANSMISSION RANGE DISPLAY CIRCUIT |
| P081C-00 | PARK INPUT CIRCUIT |
| P0914-00 | GEAR SHIFT POSITION CIRCUIT (LIGHT FAULT) |
| P0919-00 | GEAR SHIFT POSITION CONTROL ERROR (HEAVY FAULT) |
| P0928-00 | GEAR SHIFT LOCK SOLENOID CONTROL CIRCUIT OPEN |
| P0929-00 | GEAR SHIFT LOCK SOLENOID CONTROL CIRCUIT RANGE/PERFORMANCE |
| P0955-00 | AUTO SHIFT MANUAL MODE CIRCUIT GENERAL ELECTRICAL FAILURE |
| P1C73-00 | PARK SWITCH CIRCUIT STUCK |
| P1C82-00 | AUTO SHIFT MANUAL MODE CIRCUIT (SIGNAL STUCK) |
| P1CA7-00 | IGNITION SOLENOID CONTROL CIRCUIT (SHORT TO BATTERY OR OPEN) |
| P1CA8-00 | IGNITION SOLENOID CONTROL CIRCUIT (SHORT TO GROUND) |
| U0001-00 | AUTOMATIC GEARBOX SHIFTER MODULE (AGSM) CAN COMMUNICATION BUS (BUS OFF) |
| U0002-00 | AUTOMATIC GEARBOX SHIFTER MODULE (AGSM) CAN COMMUNICATION BUS PERFORMANCE (NODE MUTE) |
| U0100-00 | LOST COMMUNICATION WITH ECM/PCM "A" |
| U0101-00 | LOST COMMUNICATION WITH TCM |
| U0129-00 | LOST COMMUNICATION WITH BRAKE SYSTEM CONTROL MODULE |
| U0140-00 | LOST COMMUNICATION WITH BODY CONTROL MODULE |
| U0155-00 | LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER (IPC) CONTROL MODULE |
| U0401-00 | INVALID DATA RECEIVED FROM ECM/PCM "A" |
| U0402-00 | INVALID DATA RECEIVED FROM TCM |
| U0418-00 | INVALID DATA RECEIVED FROM BRAKE SYSTEM CONTROL MODULE |
| U0422-00 | INVALID DATA RECEIVED FROM BODY CONTROL MODULE |
| U0423-00 | INVALID DATA RECEIVED FROM INSTRUMENT PANEL CLUSTER CONTROL |
| U1701-00 | ENGINE1 (FROM ENGINE CONTROL MODULE) MISSING MESSAGE |
| U1930-00 | AGSM_OPERATIONALMODESTS (SNA) PLAUSIBILITY |
| U1932-00 | BCM_COMMAND OPERATIONALMODESTS (SNA) PLAUSIBILITY |
| U1933-00 | BCM_COMMAND (FROM BODY CONTROL MODULE) MISSING MESSAGE |
| U1934-00 | BCM_COMMAND (FROM BCM) AND BODY2 (FROM BCM) MISSING MESSAGE |
| U193C-00 | BCM_COMMAND (FROM BCM) AND ENGINE1 (FROM ECM) MISSING MESSAGE |
| U1950-00 | BCM COMMAND (FROM BODY CONTROL MODULE) MESSAGE CRC OR MESSAGE COUNTER FAULT |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.