Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2011COMPASS LIMITED, FWD, STANDARDREPAIR AND DIAGNOSISENGINE PERFORMANCEFUEL DELIVERYFUEL SYSTEMFUEL DELIVERY, DIESELSPECIFICATIONSTORQUE
2011 Jeep Compass Limited, FWD, Standard
Fuel Delivery, Diesel: Specifications: Torque
2011 Jeep Compass Limited, FWD, StandardSECTION Torque
| Description | N.m | Ft. Lbs | In. Lbs |
|---|---|---|---|
| Accelerator Pedal Nuts | 16 | - | 142 |
| Boost Pressure Sensor Bolts | 8 | - | 71 |
| Camshaft Position Sensor (CMP) | 6 | - | 53 |
| Crankshaft Position Sensor (CKP) | 5 | - | 44 |
| Fuel Filter Bracket Nuts | 6 | - | 53 |
| Fuel Filter Shield Bolts | 6 | - | 53 |
| Fuel Injector Clamping Claw Bolt | 15 + 90° | - | 133 + 90° |
| Stage 1 | + 90° | - | + 90° |
| Fuel Injector Pressure Tubes at Injector Union Nut | |||
| Stage 1 | 7 | - | 62 |
| Stage 2 | 33 | 24 | - |
| Fuel Injector Pressure Tubes at Injector Union Nut | |||
| Stage 1 | 7 | - | 62 |
| Stage 2 | 33 | 24 | - |
| Fuel Tube Bracket Bolts | 9 | - | 80 |
| Fuel Quantity Control Valve Bolts | 7 | - | 62 |
| Fuel Rail Bolts | 14 | - | 124 |
| Fuel Rail Pressure Sensor | 35 | 26 | - |
| Fuel Return Line Banjo Bolt | 32 | 24 | - |
| Fuel Temperature Sensor | 15 | - | 133 |
| High Pressure Fuel Tube Bolts | 9 | - | 80 |
| High Pressure Fuel Tubes Union Nut at Fuel Rail | |||
| Stage 1 | 7 | - | 62 |
| Stage 2 | 33 | 24 | - |
| High Pressure Fuel Tubes Union Nut at High Pressure Pump | |||
| Stage 1 | 7 | - | 62 |
| Stage 2 | 33 | 24 | - |
| High Pressure Pump Drive Wheel Bolts | 19 | - | 168 |
| High Pressure Fuel Pump Bolts | 20 | - | 177 |
| High Pressure Fuel Pump Gear Nut | 70 | 52 | - |
| Mass Air Flow Sensor | 6 | - | 53 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.