Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSJEEP2011COMPASS LIMITED, AWD, STANDARDREPAIR AND DIAGNOSISENGINE PERFORMANCESYSTEMCABIN COMPARTMENT NODE (CCN) - ELECTRICAL DIAGNOSTICSDTC TROUBLESHOOTINGU1149-LOST COMMUNICATION WITH MULTI-FUNCTION SWITCHDIAGNOSTIC TEST

2011 Jeep Compass Limited, AWD, Standard

Diagnostic Test

2011 Jeep Compass Limited, AWD, StandardSECTION Diagnostic Test

CHECK FOR AN ACTIVE DTC
NOTE:
Before proceeding with this diagnostic procedure, verify the Left and Right Multifunction Switch and Clockspring harness connectors are properly seated and verify proper pin terminal tension. A loose connection at any of these connectors may cause this DTC to set.
1. Turn the ignition on.
2. With the scan tool, read DTCs.
  Does the scan tool display this DTC as active?
  
  Yes
  - Go To 2.
  No
  - Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals, and correct pin tension.
(D506) LIN BUS CIRCUIT OPEN

Fig 1: Measuring Voltage Of LIN BUS Circuit
Courtesy of CHRYSLER LLC
1. Turn the ignition off.
2. Disconnect the Left Multifunction Switch C1 harness connector.
3. Turn the ignition on.
4. Measure the voltage of the (D506) LIN BUS circuit.
  Is the voltage above 5.0 volts?
  
  Yes
  - Go To 3.
  No
  - Repair the open in the (D506) LIN BUS circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE - BODY VERIFICATION TEST .
(F202) IGNITION SWITCH OUTPUT (RUN/START) CIRCUIT OPEN

Fig 2: Measuring Voltage Of Ignition Switch Output (RUN/START) Circuit
Courtesy of CHRYSLER LLC
1. Measure the voltage of the (F202) Ignition Switch Output (RUN/START) circuit.
  Is the voltage above 10.0 volts?
  
  Yes
  - Go To 4.
  No
  - Repair the open in the (F202) Ignition Switch Output (RUN/START) circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE - BODY VERIFICATION TEST .
(A411) FUSED B(+) (I.O.D.) CIRCUIT OPEN

Fig 3: Measuring Voltage Of Fused B (+) (I.O.D.) Circuit
Courtesy of CHRYSLER LLC
1. Measure the voltage of the (A411) Fused B(+) (I.O.D.) circuit.
  Is the voltage above 10.0 volts?
  
  Yes
  - Go To 5.
  No
  - Repair the open in the (A411) Fused B(+) (I.O.D.) circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE - BODY VERIFICATION TEST .
(Z903) GROUND CIRCUIT OPEN

Fig 4: Measuring Resistance Between Ground & Ground Circuit
Courtesy of CHRYSLER LLC
1. Measure the resistance between ground and the (Z903) Ground circuit.
  Is the resistance below 10K Ohms?
  
  Yes
  - Replace the Left Multifunction Switch in accordance with the Service Information.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE - BODY VERIFICATION TEST .
  No
  - Repair the open in the (Z903) Ground circuit.
  - Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE - BODY VERIFICATION TEST .

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.