Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJEEP2008COMMANDER OVERLAND, RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 3 (3.7L ENGINE (SERVICE INFORMATION))SPECIFICATIONSTORQUE SPECIFICATIONS
2008 Jeep Commander Overland, RWD
Torque Specifications
2008 Jeep Commander Overland, RWDSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. |
|---|---|---|---|
| Camshaft | - | - | - |
| Non - Oiled Sprocket Bolt | 122 | 90 | - |
| Bearing Cap Bolts | 11 | - | 100 |
| Counterbalance Shaft Retaining Bolt | 28 | - | 250 |
| Timing Chain Cover Bolts | 58 | 43 | - |
| Connecting Rod Cap Bolts | 27 | 20 | - |
| PLUS 90° TURN | |||
| Bed Plate Bolts | Refer to INSTALLATION | ||
| Crankshaft Damper Bolt | 175 | 130 | - |
| Cylinder Head Bolts | - | - | - |
| M11 Bolts | Refer To INSTALLATION | ||
| M8 Bolts | Refer To INSTALLATION | ||
| Cylinder Head Cover Bolts and Studs | 12 | - | 105 |
| Exhaust Manifold Bolts | 25 | 18 | - |
| Exhaust Manifold Heat Shield Nuts | 8 | - | 72 |
| Then loosen 45° | |||
| Flexplate Bolts | 95 | 70 | - |
| Engine Mount Bracket to Block Bolts | 61 | 45 | - |
| Engine to Transmission Bellhousing Bolts | 41 | 30 | - |
| Rear Mount to Transmission Bolts | 46 | 34 | - |
| Generator Mounting Bolts | |||
| M10 Bolts | 54 | 40 | - |
| M8 Bolts | 28 | - | 250 |
| Intake Manifold Bolts | 12 | - | 105 |
| Refer to INSTALLATION for Tightening Sequence | |||
| Oil Pan Bolts | 16 | - | 140 |
| Oil Pan Drain Plug | 34 | 25 | - |
| Oil Pump Bolts | 28 | - | 250 |
| Oil Pump Cover Bolts | 12 | - | 105 |
| Oil Pickup Tube Bolt and Nut | 28 | - | 250 |
| Oil Dipstick Tube to Engine Block Bolt | 15 | - | 130 |
| Oil Fill Tube Bolts | 12 | - | 105 |
| Timing Chain Guide Bolts | 28 | - | 250 |
| Timing Chain Tensioner Arm | 28 | - | 250 |
| Hydraulic Tensioner Bolts | 28 | - | 250 |
| Timing Chain Primary Tensioner Bolts | 28 | - | 250 |
| Timing Drive Idler Sprocket Bolt | 34 | 25 | - |
| Thermostat Housing Bolts | 12 | - | 105 |
| Water Pump Bolts | 58 | 43 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.