Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Jeep TJ (CANADA) L6-4.0LFACTORY OEM SERVICE PROCEDURE
Piston, Engine
PISTONS
Weight (Less Pin) 417 - 429 Grams (14.7 - 15.1 oz.)
Piston Pin Bore Diameter 23.650 - 23.658 mm (0.9312 - 0.9315 inch)
Piston Pin To Bore (Centerline To Piston Top) 40.61 - 40.72 mm (1.599 - 1.603 inch)
Piston To Bore Clearance 0.018 - 0.038 mm (0.0008 - 0.0015 inch)
Piston Ring Groove Height
Compression Rings 1.530 - 1.555 mm (0.0602 - 0.0612 inch)
Oil Control Rings 4.035 - 4.060 mm (0.1589 - 0.1598 inch)
Piston Ring Groove Diameter
No. 1 Compression 88.39 - 88.65 mm (3.48 - 3.49 inch)
No. 2 Compression 87.63 - 87.88 mm (3.45 - 3.46 inch)
No. 3 Oil Control 89.66 - 89.92 mm (3.53 - 3.54 inch)
PISTON PINS
Piston To Pin Clearance 0.0102 - 0.0208 mm (0.0005 - 0.0009 inch)
Diameter 23.637 - 23.640 mm (0.9306 - 0.9307 inch)
Piston-Pin To Connecting Rod (Press Fit) 8.9 kN 2000 ft. lbs.
Weight (Less Pin) 417 - 429 Grams (14.7 - 15.1 oz.)
Piston Pin Bore Diameter 23.650 - 23.658 mm (0.9312 - 0.9315 inch)
Piston Pin To Bore (Centerline To Piston Top) 40.61 - 40.72 mm (1.599 - 1.603 inch)
Piston To Bore Clearance 0.018 - 0.038 mm (0.0008 - 0.0015 inch)
Piston Ring Groove Height
Compression Rings 1.530 - 1.555 mm (0.0602 - 0.0612 inch)
Oil Control Rings 4.035 - 4.060 mm (0.1589 - 0.1598 inch)
Piston Ring Groove Diameter
No. 1 Compression 88.39 - 88.65 mm (3.48 - 3.49 inch)
No. 2 Compression 87.63 - 87.88 mm (3.45 - 3.46 inch)
No. 3 Oil Control 89.66 - 89.92 mm (3.53 - 3.54 inch)
PISTON PINS
Piston To Pin Clearance 0.0102 - 0.0208 mm (0.0005 - 0.0009 inch)
Diameter 23.637 - 23.640 mm (0.9306 - 0.9307 inch)
Piston-Pin To Connecting Rod (Press Fit) 8.9 kN 2000 ft. lbs.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
