1995 Jeep Wrangler S, AutomaticFACTORY OEM SERVICE PROCEDURE

Engine Controls - Specifications - 4.0L: Capacities

BATTERY SPECIFICATIONS

Application Group Cold Crank Amps @ 0Β°F (-18Β°C)
Cherokee & Wrangler
Standard 58 430
Optional 58 500
Grand Cherokee 34 600
FLUID CAPACITIES

Application (1) Quantity
Crankcase (2) 6.0 Qts. (5.7L)
Cooling System
Cherokee (Includes 2.3 Qts. For Coolant Recovery Tank) 12.0 Qts. (11.4L)
Grand Cherokee (Includes 2.3 Qts. For Coolant Recovery Tank)
Standard Cooling System 9.3 Qts. (8.8L)
Heavy-Duty Cooling System 10.0 Qts. (9.5L)
Wrangler (Includes 1.0 Qt. For Coolant Recovery Tank) 10.5 Qts. (9.9L)
Automatic Transmission (3)
Cherokee
32RH (5) 8.7 Qts. (8.2L)
Grand Cherokee
42RE (4) 8.5-11.0 Qts. (8.0-10.4L)
46RH (4) 9.8-11.0 Qts. (9.2-10.4L)
Wrangler
AW-4 (4) 8.5 Qts. (8.0L)
Manual Transmission (SAE 75W-90 API GL-5)
Cherokee & Wrangler
AX-4/5 (2WD) 3.5 Qts. (3.3L)
AX-5 (4WD) 3.3 Qts. (3.1L)
AX-15 (2WD) 3.2 Qts. (3.0L)
AX-15 (4WD) 3.3 Qts. (3.1L)
Grand Cherokee
AX-15 3.3 Qts. (3.1L)
Axles (SAE 75W-90 API GL-5)
Front (Model 30)
Cherokee 3.1 Pts. (1.5L)
Grand Cherokee 3.1 Pts. (1.5L)
Wrangler 3.8 Pts. (1.8L)
Rear (Model 35)
Cherokee (6) 3.4 Pts. (1.6L)
Grand Cherokee (6)(7) 3.4 Pts. (1.6L)
Wrangler (H/D Axle) (6)(7) 3.4 Pts. (1.6L)
Rear (Model 8 1/4 Without ABS Brakes)
Cherokee (6)(7) 4.4 Pts. (2.1L)
Transfer Case (Dexron-II)
Cherokee
Command-Trac NP231 2.2 Pts. (1.0L)
Select-Trac NP242 3.0 Pts. (1.4L)
Grand Cherokee
Command-Trac NP231 2.5 Pts. (1.2L)
Select-Trac NP242 2.9 Pts. (1.4L)
Quadra-Trac NP249 2.5 Pts. (1.2L)
Wrangler
Command-Trac NP231 (A/T) 2.2 Pts. (1.0L)
Command-Trac NP231 (M/T) 3.1 Pts. (1.5L)
(1) Fluid capacities listed are approximate. Always fill to FULL mark.
(2) Includes oil filter.
(3) Includes torque converter.
(4) Mopar ATF Plus Type 7176 fluid only.
(5) Dexron-III Mercon fluid.
(6) With trailer towing package, use Synthetic 75W-140 gear oil.
(7) With limited slip differential, add 2 ounces of friction modifier.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.