Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSJAGUAR2021F-TYPE BASE, 2D CONVERTIBLEREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 97 (DIAGNOSTIC TROUBLE CODE (DTC) INDEX DTC: IMAGE PROCESSING MODULE (IPMA) -- F-TYPE/X152)
2021 Jaguar F-Type Base, 2D Convertible
Section 97 (Diagnostic Trouble Code (DTC) Index DTC: Image Processing Module (IPMA) -- F-Type/X152)
2021 Jaguar F-Type Base, 2D ConvertibleSECTION Section 97 (Diagnostic Trouble Code (DTC) Index DTC: Image Processing Module (IPMA) -- F-Type/X152)
WARNING: This page is about a different car, the 2018 Jaguar F-Type, 2017 Jaguar F-Type, 2016 Jaguar F-Type, 2015 Jaguar F-Type, and 2014 Jaguar F-Type. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Trouble Code (DTC) Index DTC: Image Processing Module (IPMA)
- Description And Operation
- Image Processing Module (IPMA)
- Notes
- B1206-53: Crash Occured - Deactivated
- B151F-18: Auxiliary Cooling Fan -Circuit current below threshold
- B151F-19: Auxiliary Cooling Fan -Circuit current above threshold
- B151F-31: Auxiliary Cooling Fan -No signal
- B151F-91: Auxiliary Cooling Fan -Parametric
- B1DA9-92: Autonomous Emergency Braking Function -Performance or incorrect operation
- C1001-49: Vision System Camera -Internal electronic failure
- C1001-57: Vision System Camera -Invalid/incomplete software component
- C1001-78: Vision System Camera -Alignment or adjustment incorrect
- C1001-98: Vision System Camera -Component or system over temperature
- U0001-81: High Speed CAN Communication Bus - Invalid serial data received
- U0001-82: High Speed CAN Communication Bus - Alive/sequence counter incorrect/not updated
- U0001-83: High Speed CAN Communication Bus - Value of signal protection calculation incorrect
- U0001-87: High Speed CAN Communication Bus - Missing message
- U0001-88: High Speed CAN Communication Bus - Bus off
- U0002-82: High Speed CAN Communication Bus Performance -Alive/sequence counter incorrect/not updated
- U0300-00: Internal Control Module Software Incompatibility - No sub type information
- U2300-51: Central Configuration -Not programmed
- U2300-54: Central Configuration -Missing calibration
- U2300-55: Central Configuration -Not configured
- U2300-56: Central Configuration -Invalid/incomplete configuration
- U2300-64: Central Configuration -Signal plausibility failure
- U3000-44: Control Module - Data memory failure
- U3000-68: Control Module - Event information
- U3000-96: Control Module - Component internal failure
- U3000-97: - Control Module - Component or system operation obstructed or blocked
- U3003-16: Battery Voltage - Circuit voltage below threshold
- U3003-17: Battery Voltage - Circuit voltage above threshold
- Image Processing Module (IPMA)
- Description And Operation
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.