Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Jaguar F-Type BaseFACTORY OEM SERVICE PROCEDURE
Diagnostic Trouble Code (DTC) Index DTC: Rear Differential Control Module (RDCM) -- F-Type/X152
- Diagnostic Trouble Code (DTC) Index DTC: Rear Differential Control Module (RDCM)
- Description And Operation
- Rear Differential Control Module (RDCM)
- Notes
- P0562-16: System Voltage Low -Circuit voltage below threshold
- P0563-17: System Voltage High -Circuit voltage above threshold
- P0604-00: Internal Control Module Random Access Memory (RAM) Error -No sub type information
- P0605-00: Internal Control Module Read Only Memory (ROM) Error - No sub type information
- P0606-47: Control Module Processor -Watchdog/safety MicroController failure
- P0607-49: Control Module Performance -Internal electronic failure
- P062F-00: Internal Control Module EEPROM Error - No sub type information
- P0652-16: Sensor Reference Voltage B Circuit Low - Circuit voltage below threshold
- P0653-17: Sensor Reference Voltage B Circuit High -Circuit voltage above threshold
- P0657-13: Actuator Supply Voltage A Circuit/Open - Open circuit
- P0658-11: Actuator Supply Voltage A Circuit/Low - Circuit short to ground
- P0659-12: Actuator Supply Voltage A Circuit/High - Circuit short to battery
- P080A-54: Clutch Position Not Learned -Missing calibration
- P0810-62: Clutch Position Control Error -Signal compare failure
- P0CBC-11: Drive Motor "A" Temperature Sensor Circuit - Circuit short to ground
- P0CBC-15: Drive Motor "A" Temperature Sensor Circuit - Circuit short to battery or open
- P186A-13: Differential Lock-up Actuator Brake Control Circuit/Open -Circuit open
- P186B-11: Differential Lock-up Actuator Brake Control Circuit Low - Circuit short to ground
- P186C-12: Differential Lock-up Actuator Brake Control Circuit High - Circuit short to battery
- P186D-97: Clutch Actuator Stuck -Component or system operation obstructed or blocked
- P1888-11: Differential Oil Temperature Sensor Circuit Failure - Circuit short to ground
- P1888-15: Differential Oil Temperature Sensor Circuit Failure - Circuit short to battery or open
- P188A-98: Differential Oil Temperature Too High/Too Low -Component or system over temperature
- P18A5-12: Motion Position Sensor "A" Signal Circuit -Circuit short to battery
- P18A5-14: Motion Position Sensor "A" Signal Circuit -Circuit short to ground or open
- P18A8-74: Differential Actuator Brake Control -Actuator slipping
- P2787-4B: Clutch Temperature Too High -Over temperature
- U0001-81: High Speed CAN Communication Bus - Invalid serial data received
- U0001-87: High Speed CAN Communication Bus - Missing message
- U0001-88: High Speed CAN Communication - Bus off
- U0300-00: Internal Control Module Software Incompatibility - No sub type information
- U1A14-49: CAN Initialization Failure -Internal electronic failure
- U2000-4B: Motor Temperature -Over temperature
- U2011-1C: Motor - Circuit voltage out of range
- U210A-62: Temperature Sensor - Signal compare failure
- U3000-4B: Control Module - Over temperature
- Rear Differential Control Module (RDCM)
- Description And Operation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
