Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1987 Jaguar XJ-SCFACTORY OEM SERVICE PROCEDURE
Labor Times
- Accessories and Equipment
- Exterior Lights
- Gauges and Instrument Panels
- Ammeter
- Coolant Temperature Gauge (Dash Unit)
- Coolant Temperature Sender Or Sensor
- Fuel Gauge (Dash Unit)
- Fuel Gauge Tank Unit
- Instrument Cluster Printed Circuit
- Oil Pressure Gauge (Dash Unit)
- Oil Pressure Sender Or Switch
- Speedometer Cable
- Speedometer Cable & Housing
- Speedometer Head
- Speedometer Right Angle Drive
- Tachometer Head
- Headlights
- Warning Systems
- Window Motors and Regulators
- Wiper & Washer Systems
- Body and Frame
- Brakes
- Drivelines and Axles
- Electrical
- Engine Mechanical
- Auxiliary Emission Control Systems
- Air Delay Valve
- Air Injection Reactor Check Valve
- Air Injection Reactor Diverter Valve
- Air Injection Reactor Pump
- Air Injection Reactor Pump Belt
- Air Injection Reactor Pump Clutch
- Air Injection Reactor Tube
- Air Vacuum Valve
- Crankcase Vent Filter
- EGR Control Unit
- EGR Valve
- Engine Emission System
- Evaporation Control Canister
- PCV Valve
- Cooling Fan
- Cooling System (Mechanical)
- Exhaust
- Fuel Systems
- Lubrication Systems
- Mechanical
- Camshaft
- Connecting Rod Bearings
- Crankshaft
- Crankshaft Damper
- Crankshaft Main Oil Seal
- Crankshaft Oil Seal
- Cylinder Head Gasket
- Engine Assembly
- Engine Assembly (Complete)
- Engine Or Transmission Mount
- Main Bearings
- Piston Ring Set
- Timing Chain
- Timing Cover &/Or Gasket
- Valve
- Valve Clearance
- Valve Cover Gasket
- Valve Lifters
- Valve Spring Or Seal
- Starters
- Auxiliary Emission Control Systems
- Engine Performance
- Fuel Delivery System
- Air Cleaner Element
- Air Flow Meter
- Air Temp Sensor
- Auxiliary Air Regulator
- Cold Start Fuel Injector
- Cold Start Relay
- Cold Start Valve
- Coolant Temperature Sensor
- Electronic Control Unit
- Fuel Cut-Off Switch
- Fuel Injection Ballast Resistor
- Fuel Injection Idle Speed
- Fuel Injection Power Amplifier
- Fuel Injection Relay
- Fuel Injection System
- Fuel Injector
- Fuel Injector Resistor Pack
- Fuel Pressure Regulator
- Fuel Rail
- Full Throttle Microswitch
- Hot Start Switch
- Ignition On Relay
- Intake Manifold
- Intake Manifold Gasket
- Manifold Pressure Sensor
- Overrun Valve
- Oxygen Sensor
- Thermal Time Switch
- Throttle Housing
- Throttle Position Sensor
- Throttle Switch
- Trigger Contact
- Ignition Systems
- Fuel Delivery System
- Heating, Ventilation & A/C (HVAC)
- Steering
- Suspension
- Front Suspension
- Rear Suspension
- Wheel and Tire Systems
- Transmission
- Automatic Trans
- Clutch Manual and Hydraulic
Chapter Navigation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.