Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2003 Isuzu Axiom 2WD V6-3.5LFACTORY OEM SERVICE PROCEDURE
Ignition System: Service and Repair
Removal Procedure
1. Disconnect the negative battery cable.
2. Disconnect the ignition coil connector at the ignition coil assemblies.

3. Remove the two screws that secure the ignition coil assemblies to the rocker cover.
4. Remove the ignition coil assemblies and the spark plug boot from the spark plug.
- Twist the ignition coil assemblies while pulling it straight up.
5. Use the appropriate spark plug socket in order to remove the spark plug from the engine.
Installation Procedure
NOTE: The plug must thread smoothly into the cylinder head and be fully seated.Use a thread chaser if necessary to clean the threads in the cylinder head.Cross-threading or failure to fully seat the spark plug can cause plug overheating, exhaust blow-by gases, or thread damage. Do not overtighten the spark plugs. Over tightening can cause aluminum threads to strip.
1. Install the spark plug in the engine. Use the appropriate spark plug socket.
Tighten
Tighten the spark plug to 18 N-m (13 lb ft.).

2. Install the ignition coil assemblies and spark plug boot over the spark plug.
CAUTION: Ignition coil assembly #6 is different from ignition coil assembly #1 to #5. Ignition coil assemblies #6 is short type. Be careful it when installing ignition coil assembly of #6.

3. Install ignition coil assemblies and tighten the fixing bolts to the specified torque.
Torque: 4 N-m (35.4 lb in)
4. Connect the ignition coil connector at the ignition coil assemblies.
5. Connect the negative battery cable.
1. Disconnect the negative battery cable.
2. Disconnect the ignition coil connector at the ignition coil assemblies.
3. Remove the two screws that secure the ignition coil assemblies to the rocker cover.
4. Remove the ignition coil assemblies and the spark plug boot from the spark plug.
- Twist the ignition coil assemblies while pulling it straight up.
5. Use the appropriate spark plug socket in order to remove the spark plug from the engine.
Installation Procedure
NOTE: The plug must thread smoothly into the cylinder head and be fully seated.Use a thread chaser if necessary to clean the threads in the cylinder head.Cross-threading or failure to fully seat the spark plug can cause plug overheating, exhaust blow-by gases, or thread damage. Do not overtighten the spark plugs. Over tightening can cause aluminum threads to strip.
1. Install the spark plug in the engine. Use the appropriate spark plug socket.
Tighten
Tighten the spark plug to 18 N-m (13 lb ft.).
2. Install the ignition coil assemblies and spark plug boot over the spark plug.
CAUTION: Ignition coil assembly #6 is different from ignition coil assembly #1 to #5. Ignition coil assemblies #6 is short type. Be careful it when installing ignition coil assembly of #6.
3. Install ignition coil assemblies and tighten the fixing bolts to the specified torque.
Torque: 4 N-m (35.4 lb in)
4. Connect the ignition coil connector at the ignition coil assemblies.
5. Connect the negative battery cable.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
