Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2002 Isuzu Axiom 2WD V6-3.5LFACTORY OEM SERVICE PROCEDURE
System Specifications
General Specification
Engine type, number of cylinders and arrangement
Water cooled, four cycle V6
Form of combustion chamber Pent-roof type
Valve mechanism 4-Cams, 4-Valves, DOHC Gear & Belt Drive
Cylinder liner type Cast in cylinder drive
Total piston displacement 3494 cc
Cylinder bore x stroke 93.4 x 85 mm (3.677 x 3.346 inch)
Compression ratio 9.1
Compression pressure at 300 rpm 1.37 MPa (14.0 Kg/cm2)
Engine idling speed rpm Non adjustable (750)
Valve clearance
Intake 0.28 mm (0.11 inch)
Exhaust 0.30 mm (0.12 inch)
Oil capacity 5.3 liters
Ignition timing Non adjustable (20 degree BTDC at idle rpm)
Spark plug PK16PR11, RC10PYP4, K16PR-P11
Plug gap 1.0 - 1.1 mm (0.0394 - 0.0433 inch)
General Specifications - Cooling System
Cooling system Engine coolant forced circulation
Radiator Tube type corrugated (2 tube in row)
Heat radiation capacity 85,500 kcal/h
Heat radiation area 14.02 m2 (150.9 ft2)
Radiator front area 0.263 m2 (2.83 ft2)
Radiator dry weight 56 N (12.6 lbs.)
Radiator cap valve opening pressure 93.3 - 1 22.7 kPa (13.5 - 17.8 psi)
Engine coolant capacity 2.4 lit (0.6 US gal)
Engine coolant pump Centrifugal impeller type
Delivery 300 (317) or more
Pump speed 5000 plus or minus 50 rpm
Thermostat Wax pellet type with air hole
Valve opening temperature 74.5 - 78.5 degrees C (166.1 -173.3 degrees F)
Engine coolant total capacity 10.0 lit (2.64 US gal)
Torque Specifications Views

Ignition coil, Spark plug, Crankshaft position sensor and Under cover

Cylinder head cover, Cylinder head, Camshaft bearing cap, Common chamber, EGR valve and EGR pipe, Ion sensing module

Crankshaft main bearing, Flywheel, Crankcase, Oil pan, Timing belt tensioner, Timing pulley, Timing belt cover, Oil pump, Oil gallery, Oil strainer and water pump

Connecting Rod and Water Pump

Engine Mount

Cooling System Torque Specifications
Engine type, number of cylinders and arrangement
Water cooled, four cycle V6
Form of combustion chamber Pent-roof type
Valve mechanism 4-Cams, 4-Valves, DOHC Gear & Belt Drive
Cylinder liner type Cast in cylinder drive
Total piston displacement 3494 cc
Cylinder bore x stroke 93.4 x 85 mm (3.677 x 3.346 inch)
Compression ratio 9.1
Compression pressure at 300 rpm 1.37 MPa (14.0 Kg/cm2)
Engine idling speed rpm Non adjustable (750)
Valve clearance
Intake 0.28 mm (0.11 inch)
Exhaust 0.30 mm (0.12 inch)
Oil capacity 5.3 liters
Ignition timing Non adjustable (20 degree BTDC at idle rpm)
Spark plug PK16PR11, RC10PYP4, K16PR-P11
Plug gap 1.0 - 1.1 mm (0.0394 - 0.0433 inch)
General Specifications - Cooling System
Cooling system Engine coolant forced circulation
Radiator Tube type corrugated (2 tube in row)
Heat radiation capacity 85,500 kcal/h
Heat radiation area 14.02 m2 (150.9 ft2)
Radiator front area 0.263 m2 (2.83 ft2)
Radiator dry weight 56 N (12.6 lbs.)
Radiator cap valve opening pressure 93.3 - 1 22.7 kPa (13.5 - 17.8 psi)
Engine coolant capacity 2.4 lit (0.6 US gal)
Engine coolant pump Centrifugal impeller type
Delivery 300 (317) or more
Pump speed 5000 plus or minus 50 rpm
Thermostat Wax pellet type with air hole
Valve opening temperature 74.5 - 78.5 degrees C (166.1 -173.3 degrees F)
Engine coolant total capacity 10.0 lit (2.64 US gal)
Torque Specifications Views
Ignition coil, Spark plug, Crankshaft position sensor and Under cover
Cylinder head cover, Cylinder head, Camshaft bearing cap, Common chamber, EGR valve and EGR pipe, Ion sensing module
Crankshaft main bearing, Flywheel, Crankcase, Oil pan, Timing belt tensioner, Timing pulley, Timing belt cover, Oil pump, Oil gallery, Oil strainer and water pump
Connecting Rod and Water Pump
Engine Mount
Cooling System Torque Specifications
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
