Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Work Procedure
- INSPECTION STARTÂ
- Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance.
- Open engine hood and check the following:
- Harness connectors for improper connections
- Wiring harness for improper connections, pinches and cut
- Vacuum hoses for splits, kinks and improper connections
- Hoses and ducts for leaks
- Air cleaner clogging
- Gasket
- Confirm that electrical or mechanical loads are not applied.
- Headlamp switch is OFF.
- Air conditioner switch is OFF.
- Rear window defogger switch is OFF.
- Steering wheel is in the straight-ahead position, etc.
- Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge. Ensure engine stays below 1, 000 RPM.
- Run engine at about 2, 000 RPM for about 2 minutes under no load.
- Make sure that no DTC is displayed with CONSULT or Diagnostic Test Mode II (self-diagnostic results).
Is any DTC detected?
>>
GO TO 2.
>>
GO TO 3.
- REPAIR OR REPLACEÂ
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>>
GO TO 3.
- CHECK TARGET IDLE SPEEDÂ
- Run engine at about 2, 000 RPM for about 2 minutes under no load.
- Rev engine (2, 000 to 3, 000 RPM) two or three times under no load, then run engine at idle speed for about 1 minute.
- Check idle speed. For procedure, refer to Work Procedure . For specification, refer to Idle Speed .
Is the inspection result normal?
>>
GO TO 10.
>>
GO TO 4.
- PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNINGÂ
- Stop the engine.
- Perform accelerator pedal released position learning. Refer to Description .
>>
GO TO 5.
- PERFORM THROTTLE VALVE CLOSED POSITION LEARNINGÂ
Perform throttle valve closed position learning. Refer to Description .
>>
GO TO 6.
- PERFORM IDLE AIR VOLUME LEARNINGÂ
Perform idle air volume learning. Refer to Description .
Is Idle Air Volume Learning carried out successfully?
>>
GO TO 7.
>>
Follow the instruction of IDLE AIR VOLUME LEARNING. Then GO TO 4.
- CHECK TARGET IDLE SPEED AGAINÂ
- Start engine and warm it up to normal operating temperature.
- Check idle speed. For procedure, refer to Work Procedure . For specification, refer to Idle Speed .
Is the inspection result normal?
>>
GO TO 10.
>>
GO TO 8.
- DETECT MALFUNCTIONING PARTÂ
Check the Following.
- Check intake camshaft position sensor and circuit. Refer to DTC Description .
- Check exhaust camshaft position sensor and circuit. Refer to DTC Description .
- Check crankshaft position sensor and circuit. Refer to DTC Description .
Is the inspection result normal?
>>
GO TO 9.
>>
Repair or replace. Then GO TO 4.
- CHECK ECM FUNCTIONÂ
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
>>
GO TO 4.
- CHECK IGNITION TIMINGÂ
- Run engine at idle.
- Check ignition timing with a timing light.
: Timing indicator For procedure, refer to Inspection . For specification, refer to Ignition Timing .
Is the inspection result normal?
>>
GO TO 19.
>>
GO TO 11.
- PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNINGÂ
- Stop the engine.
- Perform accelerator pedal released position learning. Refer to Description .
>>
GO TO 12.
- PERFORM THROTTLE VALVE CLOSED POSITION LEARNINGÂ
Perform throttle valve closed position learning. Refer to Description .
>>
GO TO 13.
- PERFORM IDLE AIR VOLUME LEARNINGÂ
Perform idle air volume learning. Refer to Description .
Is Idle Air Volume Learning carried out successfully?
>>
GO TO 14.
>>
Follow the instruction of IDLE AIR VOLUME LEARNING. Then GO TO 4.
- CHECK TARGET IDLE SPEED AGAINÂ
- Start engine and warm it up to normal operating temperature.
- Check idle speed. For procedure, refer to Work Procedure . For specification, refer to Idle Speed .
Is the inspection result normal?
>>
GO TO 15.
>>
GO TO 17.
- CHECK IGNITION TIMING AGAINÂ
- Run engine at idle.
- Check ignition timing with a timing light.
: Timing indicator For procedure, refer to Inspection . For specification, refer to Ignition Timing .
Is the inspection result normal?
>>
GO TO 19.
>>
GO TO 16.
- CHECK TIMING CHAIN INSTALLATIONÂ
Check timing chain installation. Refer to Removal and Installation .
Is the inspection result normal?
>>
GO TO 17.
>>
Repair the timing chain installation. Then GO TO 4.
- DETECT MALFUNCTIONING PARTÂ
Check the Following.
- Check intake camshaft position sensor and circuit. Refer to DTC Description .
- Check exhaust camshaft position sensor and circuit. Refer to DTC Description .
- Check crankshaft position sensor and circuit. Refer to DTC Description .
Is the inspection result normal?
>>
GO TO 18.
>>
Repair or replace. Then GO TO 4.
- CHECK ECM FUNCTIONÂ
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but this is a rare case.)
>>
GO TO 4.
- INSPECTION ENDÂ
If ECM is replaced during this BASIC INSPECTION procedure, perform Description .
>>
INSPECTION END
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
