Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Data Monitor
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor Item | Condition |
|---|---|
| REQ SW -DR | Indicates [ON/OFF] condition of door request switch (driver side). |
| REQ SW -AS | Indicates [ON/OFF] condition of door request switch (passenger side). |
| REQ SW -BD/TR | Indicates [ON/OFF] condition of back door request switch. |
| PUSH SW | Indicates [ON/OFF] condition of Push-Button Ignition Switch. |
| IGN RLY2 -F/B | Indicates [ON/OFF] condition of ignition relay 2. |
| CLUCH SW |
NOTE:
This item is displayed, but cannot be monitored. |
| BRAKE SW 1 | Indicates [ON/OFF] condition of brake switch. |
| DETE/CANCL SW | Indicates [ON/OFF] condition of the P position. |
| SFT PN/N SW | Indicates [ON/OFF] condition of the P or N position. |
| S/L -LOCK |
NOTE:
This item is displayed, but cannot be monitored. |
| S/L -UNLOCK |
NOTE:
This item is displayed, but cannot be monitored. |
| S/L RELAY -F/B |
NOTE:
This item is displayed, but cannot be monitored. |
| UNLK SEN -DR | Indicates [ON/OFF] condition of driver door UNLOCK status. |
| PUSH SW -IPDM | Indicates [ON/OFF] condition of Push-Button Ignition Switch. |
| IGN RLY1 -F/B | Indicates [ON/OFF] condition of ignition relay 1. |
| DETE SW -IPDM | Indicates [ON/OFF] condition of the P position. |
| SFT PN -IPDM | Indicates [ON/OFF] condition of the P or N position. |
| SFT P -MET | Indicates [ON/OFF] condition of the P position. |
| SFT N -MET | Indicates [ON/OFF] condition of the N position. |
| ENGINE STATE | Indicates [STOP/START/CRANK/RUN] condition of engine states. |
| S/L LOCK-IPDM |
NOTE:
This item is displayed, but cannot be monitored. |
| S/L UNLK-IPDM |
NOTE:
This item is displayed, but cannot be monitored. |
| S/L RELAY-REQ |
NOTE:
This item is displayed, but cannot be monitored. |
| VEH SPEED 1 | Displays the vehicle speed signal received from unified meter and A/C amp. by numerical value [Km/h]. |
| VEH SPEED 2 | Displays the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h]. |
| DOOR STAT-DR | Indicates [LOCK/READY/UNLOCK] condition of driver side door status. |
| DOOR STAT-AS | Indicates [LOCK/READY/UNLOCK] condition of passenger side door status. |
| ID OK FLAG | Indicates [SET/RESET] condition of key ID. |
| PRMT ENG STRT | Indicates [SET/RESET] condition of engine start possibility. |
| PRMT RKE STRT |
NOTE:
This item is displayed, but cannot be monitored. |
| KEY SW -SLOT | Indicates [ON/OFF] condition of key slot. |
| TRNK/HAT MNTR |
NOTE:
This item is displayed, but cannot be monitored. |
| RKE-LOCK | Indicates [ON/OFF] condition of LOCK signal from Intelligent Key. |
| RKE-UNLOCK | Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key. |
| RKE-TR/BD |
NOTE:
This item is displayed, but cannot be monitored. |
| RKE-PANIC | Indicates [ON/OFF] condition of PANIC button of Intelligent Key. |
| RKE-P/W OPEN | Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key. |
| RKE-MODE CHG | Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key. |
| RKE OPE COUN1 | When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical values starts changing. |
| RKE OPE COUN2 |
NOTE:
This item is displayed, but cannot be monitored. |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.