2017 Infiniti QX50 AWDFACTORY OEM SERVICE PROCEDURE

Data Monitor

NOTE:

The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.

X: Standard, : Not applicable, : Option

Monitored item (Unit) Monitor Item Selection Remarks
ECU INPUT SIGNALS MAIN SIGNALS SELECTION FROM ITEM
VHCL/S SE-A/T (km/h or mph) X X DTRIF Displays the vehicle speed calculated by the TCM from the output shaft revolution.
ESTM VSP SIG (km/h or mph) X - DTRIF Displays the vehicle speed signal received via CAN communication.
OUTPUT REV (RPM) X X DTRIF Displays the output speed calculated from the pulse signal of output speed sensor.
INPUT SPEED (RPM) X X DTRIF Displays the input speed calculated from front sun gear revolution and front carrier revolution.
F SUN GR REV (RPM) - - DTRIF Displays the front sun gear revolution calculated from the pulse signal of input speed sensor 1.
F CARR GR REV (RPM) - - DTRIF Displays the front carrier gear revolution calculated from the pulse signal of input speed sensor 2.
ENGINE SPEED (RPM) X X DTRIF Displays the engine speed received via CAN communication.
TC SLIP SPEED (RPM) - X DTRIF Displays the revolution difference between input speed and engine speed.
ACCELE POSI (0.0/8) X - DTRIF Displays the accelerator position estimated value received via CAN communication.
THROTTLE POSI (0.0/8) X X DTRIF Displays the throttle position received via CAN communication.
ATF TEMP 1 (°C or °F) X X DTRIF Displays the ATF temperature of oil pan calculated from the signal voltage of A/T fluid temperature sensor.
ATF TEMP 2 (°C or °F) X X DTRIF Displays the ATF temperature estimated value of torque converter outlet calculated from the signal voltage of A/T fluid temperature sensor.
ATF TEMP SE 1 (V) - - DTRIF Displays the signal voltage of A/T fluid temperature sensor.
BATTERY VOLT (V) X - DTRIF Displays the power supply voltage of TCM.
LINE PRES SOL (A) - X DTRIF Displays the command current from TCM to the line pressure solenoid.
TCC SOLENOID (A) - X DTRIF Displays the command current from TCM to the torque converter clutch solenoid.
L/B SOLENOID (A) - X DTRIF Displays the command current from TCM to the low brake solenoid.
FR/B SOLENOID (A) - X DTRIF Displays the command current from TCM to the front brake solenoid.
HLR/C SOL (A) - X DTRIF Displays the command current from TCM to the high and low reverse clutch solenoid.
I/C SOLENOID (A) - X DTRIF Displays the command current from TCM to the input clutch solenoid.
D/C SOLENOID (A) - X DTRIF Displays the command current from TCM to the direct clutch solenoid.
2346/B SOL (A) - X DTRIF Displays the command current from TCM to the 2346 brake solenoid.
L/P SOL MON (A) - - DTRIF Monitors the command current from TCM to the line pressure solenoid, and displays the monitor value.
TCC SOL MON (A) - - DTRIF Monitors the command current from TCM to the torque converter clutch solenoid, and displays the monitor value.
L/B SOL MON (A) - - DTRIF Monitors the command current from TCM to the low brake solenoid, and displays the monitor value.
FR/B SOL MON (A) - - DTRIF Monitors the command current from TCM to the front brake solenoid, and displays the monitor value.
HLR/C SOL MON (A) - - DTRIF Monitors the command current from TCM to the high and low reverse clutch solenoid, and displays the monitor value.
I/C SOL MON (A) - - DTRIF Monitors the command current from TCM to the input clutch solenoid, and displays the monitor value.
D/C SOL MON (A) - - DTRIF Monitors the command current from TCM to the direct clutch solenoid, and displays the monitor value.
2346/B SOL MON (A) - - DTRIF Monitors the command current from TCM to the 2346 brake solenoid, and displays the monitor value.
GEAR RATIO   - X DTRIF Displays the gear ratio calculated from input speed and output speed.
ENGINE TORQUE (Nm) - - DTRIF Displays the engine torque estimated value received via CAN communication.
ENG TORQUE D (Nm) - - DTRIF Displays the engine torque estimated value reflected the requested torque of each control unit received via CAN communication.
INPUT TRQ S (Nm) - - DTRIF Displays the input torque using for the oil pressure calculation process of shift change control.
INPUT TRQ L/P (Nm) - - DTRIF Displays the input torque using for the oil pressure calculation process of line pressure control.
TRGT PRES L/P (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of torque converter clutch solenoid valve calculated by the oil pressure calculation process of lock-up control.
TRGT PRES TCC (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of torque converter clutch solenoid valve calculated by the oil pressure calculation process of shift change control.
TRGT PRES L/B (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of low brake solenoid valve calculated by the oil pressure calculation process of shift change control.
TRGT PRE FR/B (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of front brake solenoid valve calculated by the oil pressure calculation process of shift change control.
TRG PRE HLR/C (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of high and low reverse clutch solenoid valve calculated by the oil pressure calculation process of shift change control.
TRGT PRES I/C (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of input clutch solenoid valve calculated by the oil pressure calculation process of shift change control.
TRGT PRES D/C (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of direct clutch solenoid valve calculated by the oil pressure calculation process of shift change control.
TRG PRE 2346/B (kPa, kg/cm2 or psi) - - DTRIF Displays the target oil pressure value of 2346 brake solenoid valve calculated by the oil pressure calculation process of shift change control.
SHIFT PATTERN   - - DTRIF Displays the gear change data using the shift pattern control.
VEHICLE SPEED (km/h or mph) - - DTRIF Displays the vehicle speed for control using the control of TCM.
RANGE SW 4 (ON/OFF) X - DTRIF Displays the operation status of transmission range switch 4.
RANGE SW 3 (ON/OFF) X - DTRIF Displays the operation status of transmission range switch 3.
RANGE SW 2 (ON/OFF) X - DTRIF Displays the operation status of transmission range switch 2.
RANGE SW 1 (ON/OFF) X - DTRIF Displays the operation status of transmission range switch 1.
SFT DWN ST SW (ON/OFF) X - DTRIF
  • Displays the operation status of paddle shifter (down switch).
  • Not mounted but displayed.
SFT UP ST SW (ON/OFF) X - DTRIF
  • Displays the operation status of paddle shifter (up switch).
  • Not mounted but displayed.
DOWN SW LEVER (ON/OFF) X - DTRIF Displays the operation status of selector lever (down switch).
UP SW LEVER (ON/OFF) X - DTRIF Displays the operation status of selector lever (up switch).
NON M-MODE SW (ON/OFF) X - DTRIF Displays whether the selector lever is in any position other than manual shift gate position.
MANU MODE SW (ON/OFF) X - DTRIF Displays whether the selector lever is in the manual shift gate position.
TOW MODE SW (ON/OFF) - - DTRIF
  • Displays the reception status of tow mode signal received via CAN communication.
  • Not mounted but displayed.
DS RANGE (ON/OFF) - - DTRIF Displays whether it is the DS mode.
1 POSITION SW (ON/OFF) X - DTRIF
  • Displays the reception status of 1 position switch signal received via CAN communication.
  • Not mounted but displayed.
OD CONT SW (ON/OFF) X - DTRIF
  • Displays the reception status of overdrive control switch signal received via CAN communication.
  • Not mounted but displayed.
BRAKESW (ON/OFF) X - DTRIF Displays the reception status of stop lamp switch signal received via CAN communication.
POWERSHIFT SW (ON/OFF) X - DTRIF
  • Displays the reception status of POWER mode signal received via CAN communication.
  • Not mounted but displayed.
ASCD-OD CUT (ON/OFF) X - DTRIF Displays the reception status of ASCD OD cancel request signal received via CAN communication.
ASCD-CRUISE (ON/OFF) X - DTRIF Displays the reception status of ASCD operation signal received via CAN communication.
ABS SIGNAL (ON/OFF) X - DTRIF Displays the reception status of ABS operation signal received via CAN communication.
TCS GR/P KEEP (ON/OFF) X - DTRIF Displays the reception status of TCS gear keep request signal received via CAN communication.
TCS SIGNAL 2 (ON/OFF) X - DTRIF Displays whether the reception value of A/T shift schedule change demand signal received via CAN communication is "cold".
TCS SIGNAL 1 (ON/OFF) X - DTRIF Displays whether the reception value of A/T shift schedule change demand signal received via CAN communication is "warm".
LOW/B PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of low brake.
HC/IC/FRB PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of high and low reversed clutch, input clutch or front brake.
IC/FRB PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of input clutch or front brake.
HLR/C PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of high and low reversed clutch.
W/O THL POS (ON/OFF) X - DTRIF Displays the kickdown condition signal status received via CAN communication.
CLSD THL POS (ON/OFF) X - DTRIF Displays the idling status signal status received via CAN communication.
DRV CST JUDGE (DRIVE/COAST) - - DTRIF Displays the judgment results of "driving" or "coasting" judged by TCM.
SHIFT IND SIGNAL   - - DTRIF Displays the transmission value of shift position signal transmitted via CAN communication.
STARTER RELAY (ON/OFF) - - DTRIF Displays the command status from TCM to starter relay.
F-SAFE IND/L (ON/OFF) - - DTRIF Displays the transmission status of A/T CHECK indicator lamp signal transmitted via CAN communication.
ATF WARN LAMP (ON/OFF) - - DTRIF
  • Displays the transmission status of ATF temperature signal transmitted via CAN communication.
  • Not mounted but displayed.
MANU MODE IND (ON/OFF) - - DTRIF Displays the transmission status of manual mode signal transmitted via CAN communication.
ON OFF SOL MON (ON/OFF) - - DTRIF Monitors the command value from TCM to the anti-interlock solenoid, and displays the monitor status.
START RLY MON (ON/OFF) - - DTRIF Monitors the command value from TCM to the starter relay, and displays the monitor status.
ON OFF SOL (ON/OFF) - - DTRIF Displays the command status from TCM to anti-interlock solenoid.
SLCT LVR POSI   - X DTRIF Displays the shift positions recognized by TCM.
GEAR   - X DTRIF Displays the current transmission gear position recognized by TCM.
NEXT GR POSI   - - DTRIF Displays the target gear position of gear change that is calculated based on the vehicle speed information and throttle information.
SHIFT MODE   - - DTRIF Displays the transmission driving mode recognized by TCM.
D/C PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of direct clutch.
FR/B PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of front brake.
2346/B PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of 2346 brake.
2346B/DC PARTS (FAIL/NOTFAIL) - - DTRIF Displays whether the identified malfunction point judged by TCM is the related parts of 2346 brake or direct clutch.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.