Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Data Monitor
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
| Monitor Item | Condition |
|---|---|
| REQ SW -DR | Indicates [On/Off] condition of door request switch (driver side) |
| REQ SW -AS | Indicates [On/Off] condition of door request switch (passenger side) |
| REQ SW -BD/TR | Indicates [On/Off] condition of trunk lid opener request switch |
| PUSH SW | Indicates [On/Off] condition of push-button ignition switch |
| SHFTLCK SLNID PWR SPLY | Indicates [On/Off] condition of the power supply from BCM to shift lock solenoid |
| CLUCH SW |
NOTE:
This item is displayed, but cannot be monitored |
| BRAKE SW 1 | Indicates [On/Off] * condition of stop lamp switch power supply |
| BRAKE SW 2 | Indicates [On/Off] condition of stop lamp switch |
| DETE/CANCL SW | Indicates [On/Off] condition of P position |
| SFT PN/N SW | Indicates [On/Off] condition of P or N position |
| UNLK SEN -DR | Indicates [On/Off] condition of driver door UNLOCK status |
| PUSH SW -IPDM | Indicates [On/Off] condition of push-button ignition switch |
| IGN RLY1 -F/B | Indicates [On/Off] condition of ignition Relay 1 |
| DETE SW -IPDM | Indicates [On/Off] condition of P position |
| SFT PN -IPDM | Indicates [On/Off] condition of P or N position |
| SFT P -MET | Indicates [On/Off] condition of P position |
| SFT N -MET | Indicates [On/Off] condition of N position |
| ENGINE STATE | Indicates [STOP/STALL/CRANK/RUN] condition of engine states |
| VEH SPEED 1 | Display the vehicle speed signal received from combination meter by numerical value [km/h] |
| VEH SPEED 2 | Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [km/h] |
| DOOR STAT-DR | Indicates [LOCK/READY/UNLK] condition of driver door status |
| DOOR STAT-AS | Indicates [LOCK/READY/UNLK] condition of passenger door status |
| DOOR STAT-RR |
NOTE:
This item is displayed, but cannot be used |
| DOOR STAT-RL |
NOTE:
This item is displayed, but cannot be used |
| BK DOOR STATE |
NOTE:
This item is displayed, but cannot be monitored |
| ID OK FLAG | Indicates [Set/Reset] condition of Intelligent Key ID |
| PRMT ENG STRT | Indicates [Set/Reset] condition of engine start possibility |
| PRMT RKE STRT |
NOTE:
This item is displayed, but cannot be monitored |
| I-KEY OK FLAG | Indicates [KEY On/NOT On] condition of Intelligent Key ID and Intelligent Key is detected inside vehicle |
| PRBT ENG STRT | Indicates whether or not the engine is in start prohibited status |
| ID AUTHENT CANCEL TIMER | Indicates whether or not it is in engine start possible status when Intelligent Key verification is unnecessary |
| ACC BATTERY SAVER | Indicates [On/Off] whether or not ignition battery saver is in operation |
| CRNK PRBT TMR | Indicates [On/Off] whether or not in cranking prohibited status due to starter motor protection function operation |
| AUT CRANK TMR | Indicates [On/Off] whether or not in AUTO CRANKING MODE status |
| CRNK PRBT TME | Indicates the time for changing from cranking prohibited status to cranking possible status |
| AUT CRANK TMR | Indicates the time that AUTO CRANKING MODE operates |
| CRANKING TME | Indicates the cranking operation time |
| SHORT CRANK |
NOTE:
This item is displayed, but not used |
| ST RLY-REQ | Indicates [On/Off] condition of starter Relay control signal |
| IGN RLY1-REQ | Indicates [On/Off] condition of ignition Relay (IPDM E/R) control signal |
| IGN RLY2-REQ | Indicates [On/Off] condition of ignition Relay (F/B) control signal |
| DETE SW PWR | Indicates [On/Off] condition of the power supply from BCM to the A/T shift selector (detention switch) |
| IGN RLY3-REQ | Indicates [On/Off] condition of blower Relay control signal |
| ACC RLY-REQ | Indicates [On/Off] condition of accessory Relay control signal |
| RKE OPE COUN1 | When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the numerical value start changing |
| RKE OPE COUN2 |
NOTE:
This item is displayed, but cannot be monitored |
| TRNK/HAT MNTR | Indicates [On/Off] condition of trunk room lamp switch |
| RKE-LOCK | Indicates [On/Off] condition of LOCK signal from Intelligent Key |
| RKE-UNLOCK | Indicates [On/Off] condition of UNLOCK signal from Intelligent Key |
| RKE-TR/BD | Indicates [On/Off] condition of trunk open signal from Intelligent Key |
| RKE-PANIC | Indicates [On/Off] condition of panic alarm signal from Intelligent Key |
| RKE-MODE CHG |
NOTE:
This item is displayed, but cannot be monitored |
| RKE PBD |
NOTE:
This item is displayed, but cannot be monitored |
* : OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.