2013 Infiniti M35hFACTORY OEM SERVICE PROCEDURE

Operation When Intelligent Key Is Carried

WARNING: This page is about a different car, the 2012 Infiniti M35h. However, it is still accessible from the selected car via links, so may be relevant.

Models with steering lock unit

  1. When the push-button ignition switch is pressed, the BCM activates the inside key antenna and transmits the request signal to the Intelligent Key.
  2. The Intelligent Key receives the request signal and transmits the Intelligent Key ID signal to the BCM.
  3. BCM receives the Intelligent Key ID signal via remote keyless entry receiver and verifies it with the registered ID.
  4. BCM transmits the unlock signal to steering lock unit and IPDM E/R if the verification results are OK.
  5. IPDM E/R turns the steering lock relay ON to supply power source to the steering lock unit.
  6. The steering lock releases.
  7. BCM transmits the power supply stop signal to IPDM E/R when detecting that the steering lock is in the unlock condition.
  8. IPDM E/R turns the steering lock relay OFF to stop power supply to the steering lock unit.
  9. BCM turns ACC relay ON and transmits the ignition power supply ON signal to IPDM E/R.
  10. IPDM E/R turns the ignition relay ON to start the ignition power supply.
  11. BCM detects that the selector lever position and brake pedal operating condition.
  12. BCM transmits READY signal to HPCM if BCM judges that the READY set condition* is satisfied.

    *: For READY set condition, refer to "READY SET CONDITION TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATIONΒ " below.

    CAUTION:
    • If a malfunction is detected in the Intelligent Key system, "I-KEY system fault" on information display appears. In this case, BCM does not transmits READY signal.
    • When the Intelligent Key is carried outside of the vehicle (inside key antenna detection area) while the ignition switch position is ACC or ON, BCM does not transmits READY signal even if READY set condition* is satisfied.
  13. When BCM receives feedback signal from HPCM indicating that the vehicle is set to READY, BCM stops transmitting READY.

Models without steering lock unit

  1. When the push-button ignition switch is pressed, the BCM activates the inside key antenna and transmits the request signal to the Intelligent Key.
  2. The Intelligent Key receives the request signal and transmits the Intelligent Key ID signal to the BCM.
  3. BCM receives the Intelligent Key ID signal via remote keyless entry receiver and verifies it with the registered ID.
  4. BCM turns ACC relay ON and transmits the ignition power supply ON signal to IPDM E/R.
  5. IPDM E/R turns the ignition relay ON to start the ignition power supply.
  6. BCM detects that the selector lever position and brake pedal operating condition.
  7. BCM transmits READY signal to HPCM if BCM judges that the READY set condition* is satisfied.

    *: For READY set condition, refer to "READY SET CONDITION TABLE BY PUSH-BUTTON IGNITION SWITCH OPERATIONΒ " below.

    CAUTION:
    • If a malfunction is detected in the Intelligent Key system, "I-KEY system fault" on information display appears. In this case, BCM does not transmits READY signal.
    • When the Intelligent Key is carried outside of the vehicle (inside key antenna detection area) while the ignition switch position is ACC or ON, BCM does not transmits READY signal even if READY set condition* is satisfied.
  8. When BCM receives feedback signal from HPCM indicating that the vehicle is set to READY, BCM stops transmitting READY.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.