2013 Infiniti G37 BaseFACTORY OEM SERVICE PROCEDURE

General Precautions

  • Do not operate the engine for an extended period of time without proper exhaust ventilation.

    Keep the work area well ventilated and free of any inflammable materials. Special care should be taken when handling any inflammable or poisonous materials, such as gasoline, refrigerant gas, etc. When working in a pit or other enclosed area, be sure to properly ventilate the area before working with hazardous materials. Do not smoke while working on the vehicle.

    Fig 1: Precaution For Using Proper Exhaust Ventilation
    G04874608Courtesy of NISSAN NORTH AMERICA, INC.
  • Before jacking up the vehicle, apply wheel chocks or other tire blocks to the wheels to prevent the vehicle from moving. After jacking up the vehicle, support the vehicle weight with safety stands at the points designated for proper lifting before working on the vehicle.

    These operations should be done on a level surface.

  • When removing a heavy component such as the engine or transaxle/transmission, be careful not to lose your balance and drop them. Also, do not allow them to strike adjacent parts, especially the brake tubes and master cylinder.
    Fig 2: Precaution For Jacking Up Vehicle
    G04874609Courtesy of NISSAN NORTH AMERICA, INC.
  • Before starting repairs which do not require battery power:

    Turn off ignition switch.

    Disconnect the negative battery terminal.

  • If the battery terminals are disconnected, recorded memory of radio and each control unit is erased.
    Fig 3: Precaution For Disconnecting Negative Battery Terminal
    G04874610Courtesy of NISSAN NORTH AMERICA, INC.
  • To prevent serious burns:

    Avoid contact with hot metal parts.

    Do not remove the radiator cap when the engine is hot.

  • Dispose of drained oil or the solvent used for cleaning parts in an appropriate manner.
  • Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically.

    Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.

    Fig 4: Precaution For Touching Hot Metal Part
    G04874611Courtesy of NISSAN NORTH AMERICA, INC.
  • Clean all disassembled parts in the designated liquid or solvent prior to inspection or assembly.
  • Replace oil seals, gaskets, packings, O-rings, locking washers, cotter pins, self-locking nuts, etc. with new ones.
  • Replace inner and outer races of tapered roller bearings and needle bearings as a set.
  • Arrange the disassembled parts in accordance with their assembled locations and sequence.
  • Do not touch the terminals of electrical components which use microcomputers (such as ECM).

    Static electricity may damage internal electronic components.

  • After disconnecting vacuum or air hoses, attach a tag to indicate the proper connection.
  • Use only the fluids and lubricants specified in this information.
  • Use approved bonding agent, sealants or their equivalents when required.
  • Use hand tools, power tools (disassembly only) and recommended special tools where specified for safe and efficient service repairs.
  • When repairing the fuel, oil, water, vacuum or exhaust systems, check all affected lines for leakage.
    Fig 5: Identifying Power Tools
    G05914027Courtesy of NISSAN NORTH AMERICA, INC.
  • Before servicing the vehicle:

    Protect fenders, upholstery and carpeting with appropriate covers. Take caution that keys, buckles or buttons do not scratch paint.

    Fig 6: Protecting Fenders, Upholstery And Carpeting Using Covers
    G04874613Courtesy of NISSAN NORTH AMERICA, INC.
WARNING: To prevent ECM from storing the diagnostic trouble codes, never carelessly disconnect the harness connectors which are related to the engine control system and TCM (transmission control module) system. The connectors should be disconnected only when working according to the WORK FLOW of TROUBLE DIAGNOSES in Engine Control System and Transmission articles.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.