2013 Infiniti G37 BaseFACTORY OEM SERVICE PROCEDURE

Diagnosis Procedure

  1. INSPECTION START 

    Check which type of transmission the vehicle is equipped with.

    Which type of transmission? 

    A/T: GO TO 2.

    M/T: GO TO  7.

  2. CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect ICC brake switch harness connector.
    3. Turn ignition switch ON.
    4. Check the voltage between ICC brake switch harness connector and ground.
      ICC brake switch Ground Voltage
      Connector Terminal
      E114 1 Ground Battery voltage

      Is the inspection result normal? 

      YES: GO TO  4.

      NO: GO TO 3.

  3. DETECT MALFUNCTIONING PART 

    Check the following.

    • Fuse block (J/B) connector E103
    • 10A fuse (No. 3)
    • Harness for open or short between ICC brake switch and fuse

      : Repair open circuit or short to ground in harness or connectors.

  4. CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between ICC brake switch harness connector and ECM harness connector.
      ICC brake switch ECM Continuity
      Connector Terminal Connector Terminal
      E114 2 M107 126 Existed
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  6.

      NO: GO TO 5.

  5. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E106, M6
    • Harness for open or short between ICC brake switch and ECM

      : Repair open circuit, short to ground or short to power in harness or connectors.

  6. CHECK ICC BRAKE SWITCH 

    Refer to "COMPONENT INSPECTION (ICC BRAKE SWITCH) ".

    Is the inspection result normal? 

    YES: GO TO  15.

    NO: Replace ICC brake switch. Refer to "COMPONENT PARTS LOCATION ".

  7. CHECK ICC BRAKE SWITCH CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect ICC brake switch harness connector.
    3. Turn ignition switch ON.
    4. Check the voltage between ICC brake switch harness connector and ground.
      ICC brake switch Ground Condition Voltage (V)
      Connector Terminal
      E114 1 Ground Clutch pedal Slightly depressed Approx. 0
      Fully released Battery voltage

      Is the inspection result normal? 

      YES: GO TO  12.

      NO: GO TO 8.

  8. CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect ASCD clutch switch harness connector.
    3. Turn ignition switch ON.
    4. Check the voltage between ASCD clutch switch harness connector and ground.
      ASCD clutch switch Ground Voltage
      Connector Terminal
      E108 1 Ground Battery voltage

      Is the inspection result normal? 

      YES: GO TO  10.

      NO: GO TO 9.

  9. DETECT MALFUNCTIONING PART 

    Check the following.

    • Fuse block (J/B) connector E103
    • 10 A fuse (No. 3)
    • Harness for open or short between ASCD clutch switch and fuse

      : Repair open circuit or short to ground in harness or connectors.

  10. CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I 
    1. Turn ignition switch OFF.
    2. Check the continuity between ASCD clutch switch harness connector and ICC brake switch harness connector.
      ASCD clutch switch ICC brake switch Continuity
      Connector Terminal Connector Terminal
      E108 2 E114 1 Existed
    3. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO 11.

      NO: Repair open circuit, short to ground or short to power in harness or connectors.

  11. CHECK ASCD CLUTCH SWITCH 

    Refer to "COMPONENT INSPECTION (ASCD CLUTCH SWITCH) ".

    Is the inspection result normal? 

    YES: GO TO  15.

    NO: Replace ASCD clutch switch. Refer to "COMPONENT PARTS LOCATION ".

  12. CHECK ICC BRAKE SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check the continuity between ICC brake switch harness connector and ECM harness connector.
      ICC brake switch ECM Continuity
      Connector Terminal Connector Terminal
      E114 2 M107 126 Existed
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  14.

      NO: GO TO 13.

  13. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E106, M6

      : Repair open circuit, short to ground or short to power in harness or connectors.

  14. CHECK ICC BRAKE SWITCH 

    Refer to "COMPONENT INSPECTION (ICC BRAKE SWITCH) ".

    Is the inspection result normal? 

    YES: GO TO 15.

    NO: Replace ICC brake switch. Refer to "COMPONENT PARTS LOCATION ".

  15. CHECK INTERMITTENT INCIDENT 

    Refer to "INTERMITTENT INCIDENT ".

    : INSPECTION END

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.