Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Infiniti M37 BaseFACTORY OEM SERVICE PROCEDURE
Data Monitor
MONITOR ITEM DESCRIPTION
| Monitor Item [Unit] | MAIN SIGNALS | Description |
|---|---|---|
| RAD FAN REQ [%] | x | Displays the value of the cooling fan speed signal received from ECM via CAN communication. |
| AC COMP REQ [Off/On] | x | Displays the status of the A/C compressor request signal received from ECM via CAN communication. |
| TAIL&CLR REQ [Off/On] | x | Displays the status of the position light request signal received from BCM via CAN communication. |
| HL LO REQ [Off/On] | x | Displays the status of the low beam request signal received from BCM via CAN communication. |
| HL HI REQ [Off/On] | x | Displays the status of the high beam request signal received from BCM via CAN communication. |
| FR FOG REQ [Off/On] | x | Displays the status of the front fog light request signal received from BCM via CAN communication. |
| FR WIP REQ [Stop/1LOW/Low/Hi] | x | Displays the status of the front wiper request signal received from BCM via CAN communication. |
| WIP AUTO STOP [STOP P/ACT P] | x | Displays the status of the front wiper stop position signal judged by IPDM E/R. |
| WIP PROT [Off/BLOCK] | x | Displays the status of the front wiper fail-safe operation judged by IPDM E/R. |
| IGN RLY1 -REQ [Off/On] | Displays the status of the ignition switch ON signal received from BCM via CAN communication. | |
| IGN RLY [Off/On] | x | Displays the status of the ignition relay judged by IPDM E/R. |
| PUSH SW [Off/On] | Displays the status of the push-button ignition switch judged by IPDM E/R. | |
| INTER/NP SW [Off/On] | Displays the status of the shift position judged by IPDM E/R. | |
| ST RLY CONT [Off/On] | Displays the status of the starter relay status signal received from BCM via CAN communication. | |
| IHBT RLY-REQ [Off/On] | Displays the status of the starter control relay signal received from BCM via CAN communication. | |
| ST/INHI RLY [Off/ST/INHI/UNKWN] | Displays the status of the starter relay and starter control relay judged by IPDM E/R. | |
| DETENT SW [Off/On] | Displays the status of the A/T shift selector (detention switch) judged by IPDM E/R. | |
| S/L RLY-REQ [Off/On] | Displays the status of the steering lock relay request received from BCM via CAN communication.
NOTE:
For models without steering lock unit, this item is not monitored.
|
|
| S/L STATE [LOCK/UNLOCK/UNKWN] | Displays the status of the steering lock judged by IPDM E/R.
NOTE:
For models without steering lock unit, this item is not monitored.
|
|
| DTRL REQ [Off/On] | Displays the status of the daytime running light request signal received from BCM via CAN communication.
NOTE:
This item is monitored only on the vehicle with daytime running light system.
|
|
| OIL P SW [Open/Close] | Displays the status of the oil pressure switch judged by IPDM E/R.
NOTE:
This item is monitored only on the vehicle with VQ37VHR engine models.
|
|
| HOOD SW [Off/On] | Displays the status of the hood switch judged by IPDM E/R. | |
| HL WASHER REQ [Off/On] |
NOTE:
This item is indicated, but not monitored.
|
|
| THFT HRN REQ [Off/On] | Displays the status of the theft warning horn request signal received from BCM via CAN communication. | |
| HORN CHIRP [Off/On] | Displays the status of the horn reminder signal received from BCM via CAN communication. | |
| CRNRNG LMP REQ [Off/On] |
NOTE:
This item is indicated, but not monitored.
|
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
